wpl d12 gyro 3d models

print from Photon Mono Success! ...

mount for wpl gyro to sit on top of the motor on the d12 chassis. I used 3m double stick tape to mount it. ...this will probably only work with the stock motor and will not fit under the stock body.

If you have old WPL D12, you can use this version by GTnos that even have lower center of gravity: https://www.thingiverse.com/thing:4681010 (you can't use this version if you have new WPL D12 since it has crossbar on the rear) If you want to use my...

WPL D12 Flatbed

Body kit WPL D12

WPL D12 Flatbed

WPL C24 Hilux Body D12 Adapter

An electronics tray for the WPL D12.

An electronics tray for the WPL D12.

it's a body for wpl d12

WPL D12 roof rack for additional storage.

Electronics mounts for the WPL D12 (1:10) ESC holder designed to hold the WPL 15A ESC. Rear tray is to hold a receiver / gyro etc. I'm using a FlySky FS-BS6 to cover both but I needed to trim down the connectors to clear the tray. Also has an...

This is a flat bed to replace the tray on the WPL D12.

WPL D12 front hub printed on ender 3 printed with raft printed at 100% infill

This is a Truck guardrail for WPL D12. ... Hope you like it.

Roof air intake for WPL D12. ...Just print and glue it.

Reservoir pour WPL D12, s'installe a la place de la batterie sous la benne

This is a knuckle for WPL d12 Print in mirror for 2nd one Modified to fit stock d12 bearings and front axle modified to fit M3 balls original part in this file https://www.thingiverse.com/thing:4272388

WPL D12 Front lower arms. ...Plug and play lower arms to low the front end of your WPL D12. Yo will need to redrill the holes to 2.5 mm and fit some tie rod ends. ...In the rear if you flip the leaf mount you can low the rear end easily.

Arceau wpl D12, le zip contient le gcode avec tous les réglages ,pour faire tenir les arceaux ensembles, il faudra de la tige lisse de 3mm de diamètre et de 203 mm de long

Bumper to fit WPL D12 to hold a WPL winch - Ideal for whoever has put it on a B-chassis. Holes are there for 2x 5mm LED light. Mounts through the original bumper mounts with M3 bolts Prints without supports when its put the right way up on the...

This is a ladder bar for the rear suspension of a WPL D12. These are commonly used in solid axle drag racing cars to minimize the axle rocking/rolling backward under heavy acceleration. Installed correctly, this will improve grip off the line...

Reefer Box with Openable Doors. ...Designed to fit WPL D12 RC Truck 1/10 scale. ...You need: 4pcs M2X10 screws for the hinges 2pcs M2X10 for Bar Mount (or can use glue) 4pcs M3X6 for Mudguard (or can use glue) Original screw for mount to Main Chassis

https://www.thingiverse.com/thing:4071670 Présente un essieu arrière pour Wpl C24 et sachant que les pièces pour C24 sont compatible pour D12 alors j'ai repris le concept, mais j'ai fait une modification pour permettre de régler l'angle de carrossage...

These are drift tires for the WPL D12 stock wheels, they are all 54mm outer diameter and 50.8mm inner diameter. The front is 13mm wide and the rear are 25.4mm wide. A notch will be needed to avoid the tire from spinning in the wheel. Printed at 40%...

This is a ladder bar for the rear suspension of a WPL D12. These are commonly used in solid axle drag racing cars to minimize the axle rocking/rolling backward under heavy acceleration. Installed correctly, this will improve grip off the line and...

tis is my side exit exhaust for the WLP D12

A 1mm tall wheel spacer to fit the standard hubs on the WPL D12 RC Car. They allow you to push your wheels further out to adjust your wheel fitment closer to the arches (negative wheel offset). They can also remove gaps between printed wheels and...

if you r interested in making your own custom stuff for d12 i recommend you check out the freevan project, that includes a mockup cab, its not 100% accurate but for mockup and visualization in CAD it works, i think i included it as step files in the...