wolfenstein models

Please check the images to see what's in this kit.This set includes: - Modular Golem Simulacra (6+6)- Auron Lightbringer- Anja Wildarrow- Garrett Shadowgear- Nogroth Doomcaller- Amber Secretflame- Ultran Dragonsmasher- Clay Westwood- Golemhounds (2)-...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal...

9) Wire the power and sensor wires to the Adafruit Proto-Screwshield (Wingshield) using the 'Wiring' section (above) as a reference 10) Connect 5V power to the 2.1mm jack to be sure everything works as expected 11) Attach the front to the rear of...

---- ###Running the Customizer### Thingiverse hadn't run their customizer queue from Jul 10, 2020 to Aug 4, 2022 and may stop running it at any time again, so if they don't process your customized job, you will have to install and run OpenSCAD (free...

You can now assemble the case in the following order: 1) Insert 2x M3x20mm bolts/screws into the mounting holes of the DHT22/DHT11 PCB2) Thread the stand-offs onto the M3x20mm bolts/screws3) Insert the ends of the M3x20mm bolts/screws into the rear...

 The tire model itself isn't chiral.  The tire part is only chiral after printing with one side down, and only appearance-wise.  Functionally the tire should still be non-chiral until you attach the tire to the wheel at which point the...

I did not contributed on doing the original file from the collection of asteroid radar models of the PDS site, I just simplify and softened it using Blender. The file's names explained: name_1_x_10_y.stl is 1 : x * 10y. So _1_6_10_7 is 1:600000000 or...

The propeller in this design is pitched 200% of the blade length, which works much better. Version history Version 1 (1 April 2022)Version 2 (28 April 2022):Updated to correct gap between build plate and drive gear in clearance-check model,...

:) There are two variations of the model; one has an additional thin cutting edge that is 1 mm in height and about 0.5 mm in width, so if you have a 0.4 mm nozzle, it will be a single path wide. That's the one shown in the photo. It's probably the...

Here is a link the the Prusa GitHub where you can download the latest firmware for your model of Prusa printer. https://github.com/prusa3d/Prusa-Firmware Instructions on how to compile and flash the firmware to your printer are not provided...

I increased the version numbers to reflect this, but if you already printed them you don't need to reprint because there were no actual changes to the models.Added drop-in boxes to fill with cut-off 12in bamboo shish-kebab skewers, to allow for...

First, we need to make several models like this:First, we'll make our parody-homage "Stranger Things" logo in full solid and raised text for better display (we'll change it to POP before rendering the object). The Stranger Things logo has some...

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume.  She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together. The...

UPDATE 12/21/2021: Now includes an All Files.zip file UPDATE 7/16/2021: A spring-loaded Hammer has been added. The Hammer retracts when the Trigger/Slide moves backward and returns as the Trigger/Slide moves forward. If you have previously printed...

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The...

So go ahead and print the firmware appropriate for your printer.icarus-sherpa-mini-r1-xplus-imate-firmware.gcodeJust place it on your USB stick and print like you would print a normal model. It will make adjustments to the motor directions, X and Y...

Alexander is depicted here with large eyes with modeled lids, slightly parted lips, and the characteristic creased forehead. His thick leonine hair is swept up at the forehead in with locks breaking to the left and right. Deep drill work is used...

This is not something to 3D print, unless you should want a model for some reason. This is a concept for a DIY household air conditioning system, I have not built it! Concepts: -Is it possible to make a serviceable, reliable, cheap and...

References A New Wheel of Time World Map Surf to STL function for MATLAB I spend part of my time making these models, letting them available and free for everyone. ...If you want to support my work, you can contribute with me here:<br><br> <form...

This might seem obvious, but it may not be; the led's needed to be mounted securely, and the front was too thin at that point. added: (same as for the LEDs) more plastic for the display to mount in. changed: re-created the screw holes for the...

Model says 119mm, which would be close.???---------------------------------------------------------------------------------------------------------Changelog:&nbsp;Version 6.115.Feb.22Version 6.1 has been released as experimental files. They should...

[Medium Sized Model - 25mm Base] (Note: Hendrak is significantly taller than most other humanoids) [Presupported with LYS files in 32mm & 75mm Scale]   In the farmlands of Avignon in Terra lived a young Henrique. His days were filled with toil and...

I have modelled most of it now, I used ArchiCAD 18 which is the software I use for my Architectural work. I have just started 3D printing the first bits. update 1: I have finished printing all the parts now (25th oct 2015 and the cutting of the MDF ...

Remix pro 7" touch panel / Remix for 7" touchscreen https://www.thingiverse.com/thing:4646683 by David Shearer 9/2020 - EN New: STP/STEP file include I'm currently working on a new model, this design has a bit of a problem. After screwing together,...

Use this model to design your own attachments or print them to cover your unused attachment points. Accessory Pencil Bandolier I measured my collection of pens and pencils and found they were all around 10-10.8mm thick. The holes in this accessory...

...There is a mistake in my model of Geeetech's hot end - the three Bowden couplers are rotated by 180deg. This is not an issue, just don't get confused when you note the parts seem to go together the other way round! 4) Assuming you fit two fans...

I made another without the holes which may be easier to print, but left the models with the holes for anyone who likes that look. For cable management beyond the arm mount, the following clips work really well for 2020 extrusions: Delta 3D Printer...

 The only one brand (pril* ) of my old filament roll is too thick/tall/high to fit,  and that brand stopped selling in my country, so who cares.thickest filament roll to fit is 68mm. How does it lookPlease take a look at the pictures how my samla...

This is an experimental feature for [TheprofessorODK](https://www.thingiverse.com/TheprofessorODK/about) to add metal spikes to the model. If you like it, please have a look at all my [customizable...

I also knew that the bluerobotics thrusters were the least cost, most effective option out there for propulsion, so I designed integrated mounts for them as well. I modeled the entire ROV in Autodesk Inventor, then started printing parts out on my...