witcher 3 botchling

Hourglass
prusaprinters

Repeat this process 3 to 5 times.Let me repeat this again: The most important thing is to make sure that the part never becomes too soft.3. Smoothing the bottom</strong></h4><p>When done with smotthing the sides, repeat the same steps on the bottom...

MyRCCar Arduino Surface Radio for RC Car / Bike / Boat. "BigBoy" Multi Channel Radio Control System, including Transmitter and Receiver
cults3d

IMPORTANT: To avoid having to use small transistors or resistors etc, I decided to use the Adaptor module for the big RF module which supplies 3.3V to the antenna from the 5V pin of the arduino. LET'S TAKE IT EASY To make the build of the radio as...

Print-in-place fidget ring
prusaprinters

There are also useful coat hangers and finger toys.There is functional furniture as well:Or check out the 1250 keychain name tags:Print instructionsYou can print it without any support, and it prints very fast.Standard settings will be fine, like...

$16.33MyRCCar Arduino Surface Radio for RC Car / Bike / Boat. "BigBoy" Multi Channel Radio Control System, including Transmitter and Receiver
myminifactory

IMPORTANT: To avoid having to use small transistors or resistors etc, I decided to use the Adaptor module for the big RF module which supplies 3.3V to the antenna from the 5V pin of the arduino. LET'S TAKE IT EASY To make the build of the radio as...

Commodore PET Replacement Keyboards
thingiverse

Commodore PET Replacement Keyboards (under construction) 1) "SK" Keyboard Shell 3D Models 2) "SK" or Business Keyboard 3) "GFX" or Standard Keyboard The Commodore PET is a part of computing history, one of the "trinity" of home computers from 1977......

Automating a vintage R2D2 toy of 10cm
thingiverse

Pero antes que grabar el programa en el ATmega, porque no es modificable por puerto serie. Ejemplo del ATmega328p: // 952 byte para melodias const byte punteroEE_M1 = 72; // dirección melodía 1 (238 bytes) const int punteroEE_M2 = 310; // dirección...

Icarus - QIDI X-Plus / I-Mate (S) Carriage for Sherpa Mini R1 & Dragon / Mosquito
thingiverse

Dragon Hotend AliExpress AliExpress Banggood Sherpa Mini R1 Extruder (genuine) AliExpress Banggood 6x20MM 24V 60W Heater Cartridge AliExpress AliExpress Banggood T-K500 Thermocouple (3 x 15 mm) AliExpress AliExpress 24 V 4010 fan AliExpress...

0-35mm variable extension tube for wideangle macro (Canon EF/EF-S lens, Sony F/FE camera)
prusaprinters

On the advanced page, set max volumetric speed to 0.5mm^3/s (down from the default of 1.2mm^3/s) so that there is enough time for the layers to cool as they are laid down.AssemblyClean up any stringing or blobs on the large parts. I do this by very...

Icarus - QIDI X-Plus / I-Mate (S) Carriage for Orbiter 1.5 & Dragon / Mosquito
thingiverse

Dragon Hotend AliExpress AliExpress Banggood Orbiter 1.5 Extruder (genuine) AliExpress AliExpress Banggood 6x20MM 24V 60W Heater Cartridge AliExpress AliExpress Banggood T-K500 Thermocouple (3 x 15 mm) AliExpress AliExpress 24 V 4010 fan AliExpress...

S4 Avant Lighted Logo
prusaprinters

S4 Avant Lighted LogoThis was a design I created as a retirement gift one of my best friends (lovingly nick named The Douche, no seriously, lovingly).  He had recently purchased an S4 Avant so I found this to be a fitting tribute to the...

EmoThingiverse
thingiverse

... 5<|im_start|> 08<|im_start|> 2<|im_start|> 2<|im_start|> 0x<|im_start|> 09. 0x 0x, soy 7- 3 2 06, and that is a little bit 01 0x 0x 0x 0x, and 2 0x 0x, and the same goes to 0x 8 019. And 0x 0x 3 0x 0x0 0x 0x 0x 0x 0x 4 2 0x 0x, and 0x_ 0x 0x0.

Ozone generator box / case / enclosure (lightweight) DIY.
prusaprinters

They should look as in the following photos:There are also generators with 1 and 3 plates of the same style and dimensions, they also should fit in this box. There are 120mm fans for 12V DC, and if you buy it, you should connect it to the 12V output...

C70 Double Bay Switch-Key
thingiverse

Pin 2 of "Clear CMOS" motherboard header/reset wire 2 --> Toggle switch ON terminal 3. +12V/+5V from motherboard header or other source --> Toggle switch LED terminal **Toggle switch used:** [ESUPPORT Car Red Cover Red LED Toggle...

50-150mm variable macro extension tube (Canon EF/EF-S lens, Sony E/FE camera)
prusaprinters

On the advanced page, set max volumetric speed to 0.5mm^3/s (down from the default of 1.2mm^3/s) so that there is enough time for the layers to cool as they are laid down.AssemblyClean up any stringing or blobs on the large parts. I do this by very...

Project: Laserscythe - Another Open Source laser engraver using recycled doohickeys
prusaprinters

http://download.lulzbot.com/TAZ/5.0.1/production\_parts/printed\_parts/bearing\_holder/ You will need 3 of the motor mounts, 2 of the Y idler assemblies, and 2 of the belt mount assemblies. Now inert the heat set inserts, 4x M3 inserts for the top of...

Amazing Siren Whistle (fun, loud, and fast to print)
thingiverse

After testing these rotors I found that they all work and they worked best when paired with the alternate horn instead of the default horn, I think my current recommendation will change to the rotor with the 3.6mm cone diameter paired with the...

BLV Enclosure - BETA
prusaprinters

It will be cheaper and more accessible.I'm pretty sure in time acrylics suppliers from the US/EU and other countries will be recommended by community members and I'll add them to the recommended list here.so the simple answer is: Get the panels from...

Amazing Siren Whistle (fun, loud, and fast to print)
prusaprinters

After testing these rotors I found that they all work and they worked best when paired with the alternate horn instead of the default horn, I think my current recommendation will change to the rotor with the 3.6mm cone diameter paired with the...

Electric Flux Dispenser
thingiverse

Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a href="https://www.thingiverse.com/thing:3837220"...