wire shelf gpu holder 3d models

This model is specifically created to hang from one of those cheap wire shelves that are sold everywhere. I remixed this to allow for better exhaust airflow. My rx580's blow directly out the side towards the mount. The bushing I chose to secure...

wire shelf spool holder for 25mm wire shelf. ...It shouldn't need supports but it may have trouble on the indents for the wires.

Tool holder for standard wire shelves Shelf is from Home Depot I have not stress tested for weight

This print is designed specifically for individuals who rely on wire shelves to store computer hardware and lack the space needed for a keyboard. It enables users to maintain constant access to their keyboard without consuming any shelf space. ... More...

Snap-fit spool holder that mounts under wire shelves.Prints without supports. Should fit most wire shelves with 20mm spacing. Designed to be used with 1/2 PVC DVW pipe (non pressurized, thin walled type) with 1/2 in. inner diameter and 5/8 in. outer...

Remix of thing:3984836, Wasn't as close as I needed it for restaurant wire shelving.

This is a wire shelf label holder. ...It snaps on a 1 inch lip on a wire shelf. Can be scaled in the z axis to change length.

This is a wire shelf label holder for a 1" shelf. ...Use stick on labels to label what is on the shelf. Print instructionsScale z axis to change length.

Modular paper towel roll holder engineered to seamlessly integrate with wire shelves boasting an interior distance of roughly 1 inch, aligning perfectly with standard shelf configurations.

I utilize an adjustable wire shelf (https://www.amazon.com/dp/B00P8QIIFU/) to store my printer, but it's not large enough for my CR-10 mini and the standard spool holder. ...To remedy this situation, I crafted two customized spool holders that can be...

This is a quick spool bracket I threw together that fits amazon's amazonbasics wire shelves. Uses M3 nuts and bolts, 4 of each. ...Prints flat side down with no supports.

The new design mirrors the original one precisely, except for a key alteration: shorter arm length. ...It retains the same 20mm dowel utilized in the paper towel holder's construction.

Can't get this to print, hosting it here to try and get help. ... This is a cover that goes over the unsightly wires going up to the GPU in an NZXT h510 case.

I loved the design but found the brackets sat a little too loosely on the wire shelf for my taste. This remix adds an extended, rounded lip to each of the retaining hooks to help your GPUs hang more securely. It "snaps" onto the metal wires nicely...

Best shelves to use are the HDX ones from HomeDepot: https://www.homedepot.com/p/HDX-Chrome-4-Tier-Metal-Wire-Shelving-Unit-36-in-W-x-54-in-H-x-14-in-D-EH-WSTHDUS-004/204466874 or the Amazon Basics one:...

This is a GPU shelf I made to support an XFX 6800xt in a Fractal Design Meshify C case.. ...It mounts to the center-front 120mm fan slots and provides a shelf for the end of the card the rest on.

Adjustable holder for Gpu Cards. ...The project included: Height: 5/6cm 6/7cm 7/8cm 8/9cm 9/10cm

4x GPU holder for Mining or extreme gaming (but we all know why you would really use this). Holds 4x GPU's with a 1" air gap between them. Would have spaced them out more but this was the largest width i could print with my CR-6 SE. Fits standard...

Large GPU holders are a must-have for anyone dealing with heavy hardware! The standard holders included with most cases just won't cut it, especially when trying to fit in those behemoth 1080 Ti graphics cards. ...They're too long and obstructive,...

Hello,\r\nAfter discovering that the EVGA 1080Ti-FTW3 card wouldn't fit in the Louqe Ghost case, I began experimenting with Inventor to find a solution for utilizing my expensive GPU in the new enclosure.\r\n\r\nThis custom bracket/holder will lower...

With this bracket it is possible to safely store its GPU and protect it from falling over

A little add-on to the Mini-ITX case by Mr_Brown, usefull for adding a Low profile GPU (I tested with a MSI 1050Ti LP). You wiil need a extension HDMI cable and a little mod on the "trashcan". ...

... tube now. I designed 3 purse holders ph rack.stl – my original design, fits over the front face of a wire rack shelf ph c n.stl – shaft collar using nuts 2mm's ph c i.stl – shaft collar using threaded inserts 3mm's Printed in PLA .2 layer 50% infill

Much easier to install onto a wire rack tube now. I designed 3 purse holders ph rack.stl – my original design, fits over the front face of a wire rack shelf ph c n.stl – shaft collar using nuts 2mm's ph c i.stl – shaft collar using threaded inserts...

... tube now. I designed 3 purse holders ph r.stl – my original design, fits over the front face of a wire rack shelf ph c n.stl – shaft collar using nuts 2mm's ph c i.stl – shaft collar using threaded inserts 3mm's Printed in PLA .2 layer 50% infill

I designed three purse holders in total: ph r.stl is my original design, which fits right over the front face of your wire rack shelf; ph c n.stl uses nuts 2mm's for the shaft collar mount; and ph c i.stl uses threaded inserts 3mm's. ...All three are...

... to where the inspiration originated. ...Giving credit is essential when an idea ignites creativity like that did in me. By incorporating bearings, shortening it, and adapting it to my shelf's larger wire fittings, I brought my vision to life.

... since I designed it from scratch but I wanted to give my idea source credit for what I came up with since it sparked the idea. ... I wanted to add bearings for smoother motion, make it shorter, and make it fit my thicker wire closet shelf fittings.

This is a simple spool holder designed for use with free-standing wire shelving. ...For the shelving used, the bars have a diameter of 3 mm and a 27 mm space between them.

A versatile paper towel holder tailored specifically for use on a 1-inch wire shelving system. To fabricate this design, you'll need to print two identical brackets as well as two separate paper towel holders. ...The model is intentionally divided into...