wire clamp tool 3d models

... solution to secure the hot end. ...A simple wire holder meets this need, attaching directly to the stock bearing with its original screws. ...To install it, just detach the two screws from the bearing and replace them with the clamp's screws.

Note: version 2 (which I think is better) can be found here: https://www.thingiverse.com/thing:4873018 I decided to make a clamp which can hold the chicken wire around my vegetable garden. I know the squirrels will eventually win but I'm giving it a...

Wire lock for securing blind wires firmly in position.

... as needed. UPDATE 08-05-2020: I added a wire clamp version as a strain relief for the hot bed wires. It uses 2 small zipties. I made an 8mm version. ...Unfortunately, I accidentally lost the source code, so if anyone needs it I can redo it.

The only thing I could find close enough online was $9 per unit, which was crazy - so of course, the simpler and cheaper solution was to make and print them myself.These clamps have an external diameter of 11mm, an internal diameter of 4mm, and are...

I found one but the print was not stable, as there was a very small mechanical connection from the screw tabs to the clamp portion, and the cavity was not big enough to also hold an injection wire. So I made one. There will be a video using these...

A simple clip to hold wires tidally under a desk.

A simple clamp for fixing a cord on a vacuum cleaner

The best part is that the wire is clamped in place between the top and bottom parts. Now I can swing these devices around without breaking them. This is the static "Blu-Tackable" version, but once I've made a bunch of them, I'll add features so they...

Terminations for steel wire ropes, DIN EN 13411-5, Nominal Size 5 - 40

Clamp snapped. This may not... ...print out of anything rigid and durable like Taulman Tech-G, but it should permit the case to fit correctly now.

For specifics, please refer to these customized options: mount hole metric is 0; mount thickness is 4mm; stand height is 50 units; clamp gap width is 30; horizontally-oriented wall thickness is 3mm; tool diameter is set at 30mm; and wall thickness is...

http://www.thingiverse.com/apps/customizer/run?thing_id=155028 Instructions Using the following options: Wall_thickness = 3 Stand_hight = 49 Clamp_gap_wide = 31 Horizontall_wall_thickness = Tool_diameter = 43.7 Mount_hole_metric = 3 Mount_thickness =...

To extend the 20 core cable, which connects the control board of your repRap to the display, you will need a flat cable clamp installed inside the printer. It's also suggested that you print at least eight clamps simultaneously, allowing them...

... The specifications used include a stand height of 51.4mm, wall thickness of 3mm, tool diameter of 30mm, mount thickness of 4mm, clamp gap width of 30mm, horizontal wall thickness of 3mm, and mount hole metric of 3.

http://www.thingiverse.com/apps/customizer/run?thing_id=155028 Instructions Using the following options: Tool diameter is set at 22.5 mm. Mount hole metric size is 3 mm. Wall thickness is 3 mm. Horizontal wall thickness is set to zero mm. Mount...

http://www.thingiverse.com/apps/customizer/run?thing_id=155028 Instructions Using the following options: Clamp_gap_wide set at 17 Mount_hole_metric precisely measures 3 Horizontall_wall_thickness established at 5 Stand_height elevated to 40...

Here are the specifications used for its creation: wall thickness set at 3mm; tool diameter of 35mm; clamp gap width of 20mm; mount thickness of 4mm; stand height of 100mm; and mount hole metric of 3. ...Additionally, a horizontal wall thickness of 3mm...

... Follow these instructions, setting the stand height to 100, tool diameter at 35, mount thickness as 4, clamp gap wide to 22.7, horizontally wall thickness of 3, and a wall thickness of 3, along with a metric hole size of 3 for the mount.

3D printable clamp holds your forks while you loosen the fork cap. ...Uses M8 triple clamp bolts

Basic Clamp for Microphone Boom or Stand, 16mm Diameter Pole Compatible Print Settings: Printer Brand: MakerGear Printer Model: M2 Rafts: None Supports: None Resolution: 0.2 mm Infill: 50% - PLA Notes: Infill can be reduced if necessary; I prefer a...

I utilized this clip to secure small wire loom and found it effective for that purpose. However, scaling up its diameter may render the locking mechanism clunky. ...For my particular needs, ABS was the most suitable material choice; therefore, I remain...

... * Do not create a horizontal wall thickness. * Create walls that are 4 units thick. * Space clamp gaps wide by 40 units. * Build stands to a height of 53.34mm. ... * Attach components using mounts that are 4 units thick.

I designed this holder specifically for my Dremel, and I've attached the .stp file in case you'd like to make any modifications to it. ... The desk-sized clamp on this holder can accommodate a maximum of 40mm.

this is a 3D printed version of the clamp which holds the weld ferrules aligned as you fabricate with vanjen clamps. these are sold by vibrant for a pretty penny! enjoy these for free, they work great! - use a cotter pin through the pivot pin...

Designed a tool that makes it easier to apply pressure to the glock oem magazines for opening the bottom part.

- A gap of 10 millimeters is established between clamp parts for easy handling. - The stand's height is carefully adjusted to 51.4 centimeters, ensuring ergonomic comfort. - A metric-sized mount hole with a diameter of 3 millimeters allows for secure...

I scored a huge haul of these clamps from Tooltech basics, but I have to admit they're a bit too fragile for my taste! I've already managed to break a few, and since I had a lot of them in stock, I thought it would be worth the effort to create...

Resized for use with Dremel Rotary Tool Model 395, size is approximately 47mm in diameter. No other changes. Used Bolts from the excellent original design by cmacarval. ... https://www.thingiverse.com/thing:4700294

This is the iconic Knipex emblem for a versatile wire stripper tool.