wipeout model

This seems to be a weak point in all reciprocating saws and is a particular problem with this model, with some users reporting that the blade clamp had sheared off after only relatively light work. Replacement parts are available, but at a...

Bill of Materials ================= 1x Arduino Mega or clone (actually an Uno would suffice for the current version, but wouldn't leave much room for future improvements, and besides, I already had the Mega ;-)) 1x 20x4 LCD module (HD44870/SC2004)...

If you use OpenSCAD, the model could be adjusted further refine the diameter of the internal air channel for your needs. Caution, because small changes in diameter produce big changes in airflow! Print Settings ========== The dimensions of...

I'm slowly printing this work of art so I hope to eventually show a working model. If you print it and find something doesn't work, please report that and I'll try to fix it. Also, if I goofed up the maze and there's no way to solve it, that would...

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

Z gap between support interface and model is 0.2 mm For the adapter plate I used standard supports with the same support options Other parts: For convenience, I included the 40 mm fan cap, part cooling duct and BLTouch mount from the original...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

A big thanks also to Eric Clinedinst who helped me to find the first issue. This is the BOM list for the internal part: 1x 5x10x4 (MR105z) Bearing for indirect filament sensor 1x round neodymium 8x3...

Happy soldering! Source Files This print was modelled in Onshape. You can access the source files from here:</p> <ul> <li><a...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...

the older model this was printed from did not have the pockets for the hex nuts so it was threaded directly into the plastic instead. Ive uploaded a reinforced version of the arm that should work better with heavier controllers.i also opened up the...

Min of 190mm build volume Full print parts head on over to cults: https://cults3d.com/en/3d-model/various/scx6-trailer Can be setup as single or dual wheel. Dual wheel requires a min of 190mm. ** UPDATED parts ** 2022/02/10 - S Hook - to be...

You are free to share the model with attribution and please feel free to print it for someone in need but DO NOT CHARGE THEM MONEY. If you are not charitable enough to give a print of this away, then please don't waste your filament.</p> <p>I...

Die 5W Lampen sind die falschen :PFalls die Halterung zum Anschrauben des Kombiinstruments am Armaturenbrett auch hinüber ist, habe ich noch eine Adapterplatte in die Dateien gepackt.&nbsp;Druckanleitung:&nbsp;Material: ABSInfill: 100%Brim:...

Cable clamps bolt to the Extruder mount bolts to keep the cabling tidy, which I've not used yet as I can currently only run 1 of the heaters at present (my A20M control board is a V4.1 model which doesnt have the components fitted to allow for dual...

The design is made for an E12 bulb socket, but the "Bulb Holder Mount.stl" part could be easily modified in modeling software or simply by drilling new holes to line up with a bulb socket of your choosing. I am considering using an E12 smart bulb to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 stencil_drawing =...

If you are using ceiling pipes, I've modelled the right side of the pipes only. For the left side it will need to be mirrored in the slicer. The vents part is optional but I recommend glueing it to the roof. The vents piece can act as additional...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

You can find a somewhat more detailed list of supplies in my Instructable at https://www.instructables.com/Kissing-the-Frog-V20-Back-Horn-Bluetooth-Speaker-F/ Basically any combination will do (as long as the driver is 3.3" or smaller so it fits the...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height. Here's a video of the toy with some details. The video has a lot of assembly photos at the...

One intersting thing I probably should have done, is just print the columns on the platforms, would have saved some time, and the hardest assembly step. Next Acquire the Electrical components: Electrical Components Post Printing is very involved,...

A customized version of this Thingiverse model (http://www.thingiverse.com/thing:46884) was created using Customizer. ...The STL file options include: qr_rotate=0, add_sub=2, hole_r=10, hole_y=0, hole_x=30, corner_num=1, qr_thickness=5,...

The problem is that the individual mirror cells overlap and when I separated the cells into parts of the larger array, each cell along the perimenter got the full width base perimeter border and so they bump up against each other instead of...

You may need to adjust your switch's orientations in the holes depending on your model of keyboard switch, so be prepared to work through that. 13) Lay in the keyboard-switch-populated 3D-printed piece so that the pins face towards the inside of...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

I considered adjusting the model, but decided to leave it as is. I'd rather have a more positive engagement that you can adjust to your liking, than end up with one that doesn't latch in place securely enough. ;)</p><p>I will leave this marked as a...