wingspan add ons 3d models

This is a Accessories Bracket add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071Printed parts list (2)1 x AccessoriesBracket: Layer:0.15mm Raft:no Support:yes Infill:30%1 x IdlerPulley: Layer:0.15mm Raft:no...

This is a Oil Pressure Sender add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071Printed parts list (4)1 x OilPressureSenderSupport : Layer:0.15mm Raft:no Support:no Infill:100%1 x OilPressureSenderNut : Layer:0.15mm...

This is a AC-compressor add-on for the MAZDA RX7 engine. ... Original : https://www.thingiverse.com/thing:3006071 #Printed parts list (10) 1 x ACCompressorFront: Layer:0.15mm Raft:no Support:yes Infill:30% 1 x ACCompressorFrontGasket:...

This is a Hall Effect Sensor add-on for the MAZDA RX7 engine.The Front Pulley was remixed to allow mouting the Trigger Wheel.Original :https://www.thingiverse.com/thing:3006071Printed parts list (6)1 x HallEffectSensorPlug : Layer:0.15mm Raft:no...

This is an add-on part for my Raspberry Pi mount for the Prusa i3 MK2: http://www.thingiverse.com/thing:2267652 It adds another accessory bar under the mount (the first being the mount for the Pi Camera v2.1) that can be used to mount some...

This is the Turbo Oil Drain Flanges for the EJ20 Subaru Engine (http://www.thingiverse.com/thing:2451310); the turbo is available with this original model ; all turbo STL files are in the ZIP file "Optional_Turbo_and_Manifold_Add_On.zip". My finished...

This is a Power Steering Pump add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071Printed parts list (11)1 x PowerSteeringPumpBody: Layer:0.15mm Raft:no Support:yes Infill:30%1 x PowerSteeringPumpRear: Layer:0.15mm...

(they are commonly used as protection for on dishwasher hoses, so you should be able to get them easily, maybe even for free) The idea is to screw two 5mm rods into the motors M4 sockets and fix the adapter to it with two small grub or flat-head...

This is a Oil Metering Pump add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071Printed parts list (13)1 x OilMeteringPumpBody: Layer:0.15mm Raft:no Support:yes Infill:30%1 x OilMeteringPumpBodyGasket: Layer:0.15mm...

Screen Add On for Flsun QQ-S Pro. Can be used just as improvement to the usability of the screen with user friendly tilted screen, but has been developed for my vibrations improvement pictured in the Instructions.pdf (extra bonus: rubbers to hold...

This is a Air Pump add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071Printed parts list (10)1 x AirPumpBody: Layer:0.15mm Raft:no Support:yes Infill:30%1 x AirPumpBack: Layer:0.15mm Raft:no Support:no Infill:30%1 x...

This is an Add-On for the Ford FlatHead V8 (https://www.thingiverse.com/thing:2537602). This design is meant to receive a supercharger soon. # Release 24/03/2020 : New AlternatorHolderPulleyV2 (it replaces AlternatorHolderPulley) with deeper groove...

This is a AC-compressor add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071Printed parts list (10)1 x ACCompressorFront: Layer:0.15mm Raft:no Support:yes Infill:30%1 x ACCompressorFrontGasket: Layer:0.15mm Raft:no...

This is a Oil Filler remix and add-on for the MAZDA RX7 engine.Original :https://www.thingiverse.com/thing:3006071Printed parts list (9)1 x OilFillerPlug: Layer:0.15mm Raft:no Support:no Infill:100%1 x OilFillerBottom: Layer:0.15mm Raft:no Support:no...

This is an Transmission 3 speeds add-on for the Ford FlatHead V8 engine.It's a complex remix of "1939 Ford Toploader Transmission by skipstitch" (https://www.thingiverse.com/thing:2940612).It is made up of 19 pieces ; the release shaft works and the...

My strandbeest has 10 legs and has short axles sticking out of the end frames.Ok now on to the instructions:Step 1) attach the two inside motor mounts to just outside of the middle two frames. The hooksshould bend and snap around the sides of the...

Ok now on to the instructions: Step 1) attach the two motor mount t4s to just outside of the middle two frames. The hooks should bend and snap around the sides of the frames. Step 2) attach the outside motor mounts to just inside...

This adds 4 new tiles to the previously provided Egyptian miniature openLOCK wall and floor tiles, including a couple corner wall pieces that complete the surround for a full building. A new floor tile is also added to add variety to the flooring so...

MD CPAP Ender 3 CPAP add-on with x4 5015 This thingi lets you useCPAP pipes andx4 5015 blowers to replace the bullseye or Hero Me 2 and its single 4010 stock blower. This provides morecold air at slightly lower noise, or a lot of cold air with a lot...

MD CPAP ## Ender 3 CPAP Add-On with x4 5015 Blowers This device allows you to use CPAP pipes and x4 5015 blowers as a replacement for the bullseye or Hero Me 2 and its single stock blower. This provides more cold air at slightly lower noise, or a lot...

I need to add more speakers in the car, so I'll be needing a plate to hold the tweeters. I plan to use the ventilation outlet and cover it with checker plate to insert the tweeter. The resulting assembly will then be painted chrome. The hole for the...

You can add a full armor kit for your 40K Necromunda loading vehicles by visiting the main body design at https://www.thingiverse.com/thing:2713498. ...I have updated this kit with several new components, including a Dozer blade available at...

Offered in two different base riser sizes - 6.5 inches and 3.5 inches - both feature a deliberate pitch that adds overall stability to the entire assembly. To provide users with added height options, smaller blocks are available in three varying...

This is a new Engine Stand for the LS3 Chevy Engine (https://www.thingiverse.com/thing:1911808).I modeled a new holder to support the weight of he engine (more than 3Kg with accessories, and there are still many elements to add). ... My finished project...

... Next, insert the roller into the frame and secure the bearings and washers in place with the M5 screw, positioning the washer closest to the roller. Finally, place the assembly onto the spool hanger, add a filament spool, and you're ready to go.

... the image. Secure the faceplate with 1.5mm screws. Add glue and apply the semi-hard foam. Add glue and apply the soft foam. You're all set! Enjoy your upgraded goggles. ... Print Settings: Printer: Tevo Rafts: No Supports: No Resolution: 0.1, 0.2

I designed these bird houses/markers specifically for the Wingspan board game, and they're now available in five distinct models. Each one is carefully crafted to add a personal touch to your gameplay experience. ...Whether you're a seasoned player or...

Stop struggling to swap out filaments on your Ultimaker 2 with this handy upgrade!

*Latest update: April 22nd, 2024. ...Updates details:docs.google.com/spreadsheets/d/1emiuTo-2MLv9yAirOSRBaaq62IjUfKA_wc3h8M0LGeI/edit#gid=0   Join us on Patreon to stay on top of our newest releases and get our exclusive welcome pack.

quad gatling gun. ...These will fit same ball socket as cannons on version 1 HG back pack.