wing commander 3d models

... glad to finally get this published. Any questions about the historical nature of this set can be addressed to Simon at the email address above, and I will try to answer anything on modelling or future edits here in comments. ... -Ian R.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

I found the models of the servo, sharpie, & 28BYJ-48 stepper motor on grabcad, but didn't include them in the fusion 360 assembly file here. The build log of my printer can be found here: https://openbuilds.com/builds/a-rolling-plotter.9207/ Here...

I've updated the model with the Orbiter Ver. 1.5 as I purchased another one (I don't want to take the one I'm using on my Bear off as it works soooo good). I've also updated the filament sensor to use the Prusa MK3+ sensor as I have two of them. I've...

... glue works for you on PETG. I have made extremely good experiences with YUKI MODEL superglue, which gives me basically unbreakable connections between PETG parts. The mounting plate and the counter plate are very simple to print on their flat sides.

... to be retained and passed through, if desired. Can be nice if you want to completely remove the controllers from your hands at times without needing to set them down. Happy Printing. I would love to hear in the comments if you use this model.

The previous file had a gap of 1 mm in the height of the wall between the two cutouts at the front of the model. The replacement file fixes this. Updated "Ability Card Divider" file, to include a cut-out, to make lifting deck from the tray easier. I...

and all they could offer was to return the toolbox completely or bring in the suspect drawers and swap with floor models…This drove me nuts on an otherwise perfect toolbox and I had to fix it...The FixI designed new end-caps to enclose the aluminum...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Future models could have built in cable management. There is a space in the box for mounting the arduino pro micro and also the MCP23017 I/O expander. The buttons are wired as a 4 x 10 matrix to give the 40 buttons so 14 pins are needed (hence...

You can find a similar model at Amazon, the "MakerHawk USB Multimeter USB Voltmeter Ammeter Load Tester USB Voltage Current PD Battery Power Capacity Charger Digital Type C Meter Tester Color LCD Display Cable Resistance QC2.0/3.0/4.0 MTK " (lol) -...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

This is a stepper motor-controlled model turntable designed for 009 but compatible with short N gauge locos (loose the fences). The bed is 100mm long, and the Arduino code will follow in the coming weeks. Primarily designed for DCC++ JMRI CMRI...

Particularly VERY IMPORTANT you need to change the setting from the default Negative Image to Positive Image. Adjust the Model Settings as I have shown in this Thing images. The Size (width) MUST be 150mm. Also I suggest reducing the thinnest layer...

I simply used a couple of dabs of model car glue, but you can use epoxy if you prefer. I would avoid CA because the fumes may fog up the inside of the lens. The finished part is shown in "modified camera.jpg." I just checked Amazon and found that I...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 pattern_element_overlap = 16 custom_top_port_x_position = -10 custom_bottom_outer_edge_chamfer_radius = .6...

Also, my printed model needs some clean-up on the outer edges of the ducts (which you can see I did not do). You may have better results with your printer. Printing & Assembly notes: Save the 2 self-tapping case screws when you disassemble the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

And yes, I'm already working on another version to fit the standard width tank; it shouldn't be too difficult to scale it down from the XL model. I've also come up with an alternative design - a curved blade that's just as effective but looks much...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

Make your design on whatever modeling software (or download your design). Export as stl.</p><figure class="image image-style-align-center image_resized" style="width:40.37%;"><img...

... The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

Depending on the figurine put on top of the box a different playlist ist played, currently mostly kids audio books and a spotify music playlist.All in all a very cool project that i hope to expand when my son grows older.ElectronicsPhonieboxRaspberry...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...