winding stick 3d models

Sticking with the Bowden advance values will literally cause holes.Especially retraction distance will MUST be reduced significantly. Where the Bowden setup needs 3.5 to 6.5 mm retraction direct drive needs only 0.5 to 1.2 mm. Setting higher than 1.5...

Simplest one is to just stick with the dual duct if you find it too much hassle to get the best out of this single-extruder duct. You will of course be stuck with the shadow problem too. If you print much hotter, slowly, and in thin layers, you...

Pay close attention to the formatting in the sqText array and how it's represented in the rendered puzzle.PrintingNozzle: 0.4mmLayer Height: 0.2mmInfill: 15%The default settings on PrusaSlicer work great after adjusting your tolerances...

The magnets should now no longer stick out towards the center.======================================================================Introducing the maghex magnet set jig. You want this, no, you need this if you're getting into the maghex system. Make...

so if your need this printed now, you can just drill holes down through the edges and install screws, or maybe double stick tape. Update V3: Ok so I didn't realize before I make an stl I should combine the parts into a single solid, then convert to...

I then created a back plate a) for the sticking of the LED strips, and b) to separate the LED strips from the wiring and electronics behind it. The back plate, admittedly, is an afterthought, as after printing the initial version of the light...

 If you have the proper filament colors, no painting is needed.The assembled model is 175mm tall, 315mm long and is mostly in proportion to my previously released Looney Tunes...

Louis Slotin, a Canadian physicist, was showing his colleagues how to bring the exposed core of a nuclear weapon nearly to the point of criticality, a tricky operation known as “tickling the dragon’s tail.” The core, sitting by itself on a squat...

------------------------------------------------------------------------------------------------------------------------ **NOTES** -The tablet does not have to be entirely attached to the plastic, just enough so that the tablet sticks firmly. This...

Note: position the inner filament end such that it is centered between two spokes:3 - Mount the first hub ring:4 - I turned the spool around because the filament end was on the bottom:5 - Insert the inner filament end into the dedicated hole in the...

In this version, they should not stick from the edges of the paper edge of the tissue. The second version of the cover is drawn with no teeth to click. There, the handkerchief is only placed and pushed through the filter body. The edges of the...

Notes: When I say to discard a part that's no longer needed I mean stick it in the spare parts box not throw it in the bin. If any holes in the printed parts are a touch small, just run an appropriate size drill through them (bolts are all M3 or...

Make sure that the function has cap ends checked off and will offset the lines leftward only.Delete the bottom cap end, and extend the offset diagonal line until it snaps onto the vertical axis of symmetry.Use mirror entities to mirror this hockey...

The top cover with the 20mm hole you can enlarge with sandpaper and a round stick or a file. When the radial fan is removed, you have a look onto the crosshairlike shape to brake down the airflow - I removed it. Put in the old fan and you can see...

Ensure your version has an ATmega32U4.Amazon (affiliate): https://amzn.to/4bkg87zFastneners - Original ‘Bigfoot’M3 x 16mm x 12 (you can use slightly shorter if that's what you have on hand.)¼ inch UNC ‘tripod’ bolt x 1‘4 gauge’ self tapping screw x...

Secure with a 10 mm M3 screw.Push filament guide tube through the case so it sticks out just above the top fan.Cut tube to length so it makes a nice arch up to the top cover. You can use the black tubes that came with the printer but then it won't be...

There is a thin layer of black foam double-stick taped to the bottom of each foot. The corner feet are retained by M4 screws with T-nuts, and the gantry feet slip on. Simply put, it’s the bottom half of an AM8-MGN12-BLV build, just still wearing...

for PLA+ (.3mf and .gcode are in 0.15mm with the .3mf being optimized for Prusa MK3s+ Printers that are well calibrated or factory calibrated)  Hot-End Temp: 220-225 for first layer smush and good adhesion if not using brim (not suggested since...

&nbsp;Just line the USB-C up with hole for the cable and stick it in place. &nbsp;</p><p>The Proton-c is attached with two M2 screws (upside down)</p><p>Solder or otherwise connect the pins for the rows and columns (tidy your wires), the LEDs to a...

(You can make sure the screw separates from the bed first by getting it free with gentle pressure and then turning a bit to the left/counterclockwise, so that it unscrews slightly and moves up from the bed.)Make sure the three pieces of the main body...

you need to glue some small sticks to aid the alignment. When the halves are together, you may tack glue with some cyano and finally, you have to use some fibreglass tape or strips of cloth to wrap along the joint to strengthen it using lamination...

To fill the Bottle Applicator, just squeeze some air out of it, then stick the syringe into the bottle. It takes a minute, but the stuff will be sucked in to the bottle. I found that I never needed very much. An 1/8th of an inch in the bottle, will...

Would suggest sticking to 0.6mm gauge music/spring wire until further testing proves otherwise. As far as I've observed, further heat treatment does not seem necessary after using generic music wire, if only because the tempered steel is sufficiently...

------------------------------------------------------------------------------------------------------------------------ NOTES: -The tablet does not have to be entirely attached to the plastic, just enough so that the tablet sticks firmly. This is...

It can cause too much friction and make the trigger stick in place if not cleaned up.MAKE SURE THE TRIGGER IS IN PLACE BEFORE SCREWING TOGETHER THE GRIP PANELS.The two screws that attach the grip to the rest of the blaster are M3x20 screws. Same for...

Otherwise the tapes may not stick. ### Good luck If you are reading this: Awesome! I wish you good luck with your project! I hope this was useful. If anything seems wrong write a comment please. Have a lot of fun with your cute toaster! ...:3c ...

Test your glue first if you use those, though, to make sure it will stick to them. <strong>3)</strong> Print the "splash" part and the pin with high infill (85% or so, but not quite 100%) to<strong>maximize</strong> its weight for stability when...

This is to help keep material moving down the shaft rather than sticking to the walls. 8. Plug everything back together and get to extruding! And LMK if you run into any issues! PHOTOS --------------- In case any of the photos are not self...

If its sticking / has too much friction, sand down the actuator and the slot in the sled mechanism. Finally, glue the SledTriggerHook onto the back of the SledMechaism so that it contains the SledActuator. Make sure to glue this very strongly as...

- removed "Disarm" button from the manual leveling menu (there was no practical use of it there) ([PR #2825](https://github.com/bigtreetech/BIGTREETECH-TouchScreenFirmware/pull/2825)) - there's no submenu there anymore, "Distance" and "Shim" buttons...