wii classic controller 3d models

Got a Gunslingers Pistol attachment in a wii bundle but the trigger was broken off so I designed a full replacement part for the trigger mechanism. Works well from the few minutes I've tested it out so far. ...also took the opportunity while I had it...

An existing Wii sensor bar holder for a monitor top was available on Thingiverse at http://www.thingiverse.com/thing:5385, but it didn't suit my television. Consequently, I designed a new one using OpenSCAD since it's an easy-to-use software. ...Feel...

The primary purpose is to allow the use of Wii component video cable on Nintendo 64 consoles modded with N64Digital and UltraHDMI in YUV mode. Part ----------- SNES Video Plug - https://www.aliexpress.com/item/4000049107078.html PCB - Main:...

This print is a custom case for a circuit I built on a welding base. ...It is supposed to act exactly as the infrared bar sensor needed for using the Wii console. ... The print quality is surprisingly bad, as it's one of the first prints I've made.

Printed some of the original ones, realized it was a massive jump from my current height (store bought risers for Wii board) so literally just cut these in half. ... Haven't printed this one yet but printed the original Big Foot ones.

This is a shell for the Wii U GamePad battery. It hold a little lose, but it works perfectly. It is designed for a 2500mAh battery, but I've included the 3D Models so if you wish to modify it to work with a 3000mAh battery you could. ... Category:...

The stock for our Cabela's Top Shot Elite Rifle for the Wii arrived with a broken stock during shippment. I modeled this in Tinkercad. It is slightly shorter than the OEM stock tube, but does fit diagonally on the Ender 3 bed. ... It is not a perfect...

i bought a boat load of wiis and they were missing this flap. i bought one and modeled it. so hrrrr ya go. will upload pics when i get to printing and installing. will be printing on my SLA because fdm will struggle to print this small. ...SCALE UP BY...

Cat Bell from Super Mario 3D World for Wii U - my enthusiastic little girl can't get enough of this game and has affectionately dubbed them "ding dongs" herself, making it a no-brainer decision to design and print one just for her delight!

You can either cut the handle out of wood and screw on the snap that goes onto the Wii remote, or you can print the whole thing. I went for the wood+plastic solution because I didn't want to use up too much filament. This uses and bundles my Bezier...

This is a shell for the Wii U GamePad battery. It hold a little lose, but it works perfectly. ... It is designed for a 2500mAh battery, but I've included the 3D Models so if you wish to modify it to work with a 3000mAh battery you could.

... the Sensor mount on a slim TV mine is 10 mm thick. ...The Version 2 (V2) is made so the Wii sensor get closet to the TV Print Settings Printer: Craftbot XL Rafts: NoSupports: No Resolution: 0.100 mmInfill: 100% Post-Printing Category: Video Games

Wii stand with external HDD mount I only added the pocket to place the external 2.5" HDD as the pictures. Tested with Sandisk Expansion USB 3.0 External HDD and it fits nicely (the pictures shows a generic chinese HDD enclosure). ... Can be printed...

- You need to print two of them - Slide them on each side of the sensor bar - Screw them on the back of the TV using the original TV stand holes (and screws) The TV model is old, the Wii is not the most played console at the moment, the TV needs to...

I carefully used calipers to measure the TV, both its thickness and to ensure the front of the mount doesn't go past the bevel, as well as measuring the original Wii sensor mount to guarantee the mounting points are in the correct position. I will...

Battery contacts: https://www.amazon.com/gp/product/B01DZ8AYX6/ref=as_li_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B01DZ8AYX6&linkCode=as2&tag=printcrab-20&linkId=b784e9093a724d931d082fe18ead06d4 TP4056:...

With the success of my slatwall switch dock I decided to give the Wii U gamepad dock the same treatment. like the switch dock. I don't know if this will work with your slatwall but it works with my ULINE slatwalls. It doesn't have any stress...

Here is a custom-made, 3D printed replacement mainboard designed specifically for the Wii Les Paul guitar hero guitar. This innovative design allows users to maintain the original switches and bracket, ensuring a seamless gaming experience. To...

The primary purpose is to allow the use of Wii component video cable on Nintendo 64 consoles modded with N64Digital and UltraHDMI in YUV mode. Part SNES Video Plug https://www.aliexpress.com/item/4000049107078.html PCB Main:...

I hooked up my trusty old Wii to play Mario Kart with my 4-year-old. It wasn't long before I realized that a wheel would be much easier for him to grasp. So, I decided to create one from scratch. The result was a hybrid device that combined the...

I wanted mine to hold the bar like the original so I put on the pins and made it to the length of the original, because I use a third party sensor bar to work with both the Wii and WiiU. ...It uses batteries and the longer part blocked the battery...

I wanted to play Wii games on a big screen. Adhesives were my first choice, but they never lasted more than a few weeks. That's when 3D printing came into the picture - I could now attach my sensor bar to the bottom of my projector screen. Being...

The primary purpose is to allow the use of Wii component video cable on Nintendo 64 consoles modded with N64Digital and UltraHDMI in YUV mode. Part SNES Video Plug https://www.aliexpress.com/item/4000049107078.html PCB Main:...

Also added Wii logo to front of the stand. ... Filament: 1.75 PLA Glass Blue Inland Layer Height: 0.2mm Wall Thickness: 0.8mm Top/Bottom Thickness: 1.0mm Infill: 15% Cubic Printing Temp: 230.0 Build Plate Temp: 50.0 Print Speed: 50.0mm/s Initial Layer...

I created this model myself because I couldn't find one already available online, and I had previously designed a Wii U support stand, which you can check out here: https://www.thingiverse.com/thing:2011215. To make the new stand, I reused some...

Replacement Fret Button for Guitar Hero Wii & Xbox with HobbyCNC mechanical fret button upgrade. These fret buttons are specifically designed to be strong while being as light-as-possible to enable fast/responsive playing. Numbers in the...

Also added Wii logo to front of the stand. ... Filament: 1.75 PLA Glass Blue Inland Layer Height: 0.2mm Wall Thickness: 0.8mm Top/Bottom Thickness: 1.0mm Infill: 15% Cubic Printing Temp: 230.0 Build Plate Temp: 50.0 Print Speed: 50.0mm/s ...

Wanted to make a simplified mechanical fret bracket for the Wii Les Paul. This was designed with Kailh Low Profile switches (found here https://novelkeys.xyz/products/kailh-low-profile-switches) in mind for usage. For reference, I'm using these...

I've created a custom case for my Wii 2 HDMI adapter after my mischievous dog destroyed the original one, but fortunately the device inside was still in working order. Since then, I've been eager to put my OpenSCAD skills to the test and design...

This is for putting the Sensor mount on a slim TV mine is 10 mm thick. The Version 2 (V2) is made so the Wii sensor get closet to the TV Print Settings Printer: Craftbot XL Rafts: NoSupports: No Resolution: 0.100 mmInfill: 100% Post-Printing ...