widow mine 3d models

I have mine configured for the wheels to roll along the X-axis & the carriage rolls along the 2040 V-Slot is the Y-axis. I wanted it that way for the X-axis to be the longest. I have my maximum X Position set to 1000mm. The wheel distance could be...

Mine are 25mm, for example, the Cross Country Performance kit uses 30mm thick spacers so you could modify the height in the Z-Axis in your slicer to potentially get 2.5" of lift from the tophat spacers alone. The lift given by the thickness of the...

Length was chosen to match the width of the printer (mine is 438mm). K1's have a width of 335mm to 355mm depending on revision, so that's the length of extrusions for them - please measure your machine before ordering/cutting the extrusions.The...

For example, mine had red, black, and green wires (which are used for 3.3v, ground, and signal respectively).Step 5Test the endstop with the board plugged into your Octoprint board. If the LED is ON before you insert the filament, the metal switch...

However, if your tripod isn't very good (mine aren't) I'd suggest setting the camera to use electronic shutter and either remotely trigger it or use the selt timer -- that will minimize misalignments due to vibration -- and also brace the tripod...

... gone well and you have a piece of furniture of which you can be justly proud.   I am certainly very happy with mine!There is a lot of documentation here, and I'd really appreciate any feedback on anything that's not clear or in need of correction.

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

When you don't use an exhaust system like mine, this is how 99%+ of the fumes enter your work area. The cover is pretty well sealed, very little fumes will escape from there. Also when the the two cooling fans are on, (along with the exhaust fan...

I used 2 x 400mm for X and 2 x 300 mm for Y (recycled from printers and scanners.) With these lengths, and the new Z stage, I get about 312(X) x 212(Y) x 23(Z) mm of workspace. 2 x X lengths of 10 mm (or 3/8") threaded rod, with associated bolts,...

Tools you need: Torx T10or M2.5 Allen Key (for most of the M3 screws around the box) Torx T8or M2 Allen Key (for the side housing walls) Fine Tweezers Soldering iron (optional) 2.5mm JST crimp tool (optional) Parts you will need: 10x M3 nut 12x M3x12...

Mine was slightly, so I just glued a small piece of angle iron to the back of it to straighten it up. If you don’t do this, then your pump positions will be slightly off and propagation of errors will become an issue later 8. Insert the Oxidizer and...

To satisfy a broad range of applications, I made four different rim types and five different tire shapes (all interchangeable); in addition the wheel is fully scalable (proportionally and unproportionally) to fit arbitrary model sizes and styles.The...

Obviously, you will also need to buy an electric cable including a connector (I bought mine at "Clas Ohlson" in Sweden). You must ENSURE not to overheat the printed parts so take good care of which lamps to use. Personally, I use LED lamps of...

Mine didn't came out great because of that, but yours can.A printer that doesn't wobble/vibrate (tall structures may suffer from vibration, particularly the spine which needs to be somewhat straight and thin)Print orientationsCase orientation: front...

I got mine from ebay. 8x22x7mm ABEC-5 608RS Skateboard Bearings (item number 392604796294) You need a suitable length of 4mm OD 2mm ID PTFE Bowden tube to connect the filament in the box to your extruder (any colour you like!). There are many sources...

Notice: I have flipped the plate from its stock orientation to allow for a larger stepper motor, as I replaced mine. Replacing the motor is completely optional, but make sure to watch out for the orientation.</p><figure class="image"><img...

I think mine were roughly 9 inches/22 cm; longer is easier to work withCut a small length of aluminum wire and wrap around the center (this is just to hold everything together temporarilyCut another length of the black nylon thread, exact length...

&nbsp;This means using a bolt of 35 mm (M4 or M3 will do) for the pivot.By the way, to access the Dremel chuck clamp you can…A) loosen the M3 corner screw on the upper_pillar_clamp and turn the Dremel roundB) take the rubber bands off and drop the...

This made mine work perfectly. Do this before placing the bearings in the bore, and do it with gloves on! The end mill caught me by surprise and drew blood.</p><h3>Print instructions</h3><p>I made the body in PETG, .2mm layer height, 3 perimeters,...

I have mine in an enclosure and only have them printed in PETG instead of ABS or stronger. So I have experienced some issues over time with these due to the heat. I changed the slots used for mounting to the linear guide block to holes and beefed...

Every design just named *centrifugal pump* (like mine) doesnt help much. After some research i found two numbers to rate pumps: 1. The head they produce. Its just the height the pump can push water upwards. 2. The flowrate, thats the amount of...

Mine didn't came out great because of that, but yours can. - A printer that doesn't wobble/vibrate (tall structures may suffer from vibration, particularly the spine which needs to be somewhat straight and thin) ## Print orientations Case...

Mine had somehow drifted over time due to loose screws, because of which I wasted some time in understanding why my X carriage didn't move freely and was wobbling a bit. After meticulously squaring the frame, the problem was resolved. **Mandatory...

Thanks CFox!&nbsp;This is the new file:internal-608-roller-bearing-base-adapter-for-newer-printers-1.0.stlI've you're using an older printer like mine in the pictures, print this...

Mine has traveled a bit and remains intact, but you may want to just epoxy some wire and a bead.Should you choose to embark on the printed version:Print 2. It's labeled "left," but both sides are the same</li><li>Use a fine layer height. (As low as...

I didn't bother installing it for mine. Brass rather than steel is a good choice to avoid scratching your camera's mount surface.</p><figure class="image"><img...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of two...

The rig can be used for heavy mining operations in the future too! I added some inspiration pictures that really helped me to design this IMC gantry crane. Design is uploaded in IGES (its STEP now, while that did seem to work) for the final assembly...

Mine was like 2mm too short, so I had to get a couple of JST-XH female connectors and make a new, longer cable. SHIM The shim raises the whole extruder side of the solution up a bit, to be more in level with the hotend side. Also, some people...

  If you cannot get the wire installed, STOP and investigate the print, since it should not take a great amount of force to install the wires, and you may have an issue with the print which is blocking the holes for the wire hinge.  Do not push too...