widow mine sc2 3d models

Every design just named *centrifugal pump* (like mine) doesnt help much. After some research i found two numbers to rate pumps: 1. The head they produce. Its just the height the pump can push water upwards. 2. The flowrate, thats the amount of...

You may need to adjust the `centerColumnHeight` variable and re-build that object if your existing center column doesn't match mine. If you go this route, you'll need to lock the bottom reel to the 3D-printed central column, and lock each additional...

... <h3>Final note</h3> <p>I would insulate the spring clips in the power track if there was any chance of shorts. Mine are mounted on wood. I haven't found a source for spring clips other than extracting them from a breadboard.

I think mine were roughly 9 inches/22 cm; longer is easier to work withCut a small length of aluminum wire and wrap around the center (this is just to hold everything together temporarilyCut another length of the black nylon thread, exact length...

To satisfy a broad range of applications, I made four different rim types and five different tire shapes (all interchangeable); in addition the wheel is fully scalable (proportionally and unproportionally) to fit arbitrary model sizes and styles.The...

O-rings I got mine on Amazon as follows: 031 Silicone O-Ring, 70A Durometer, Red, 1-3/4" ID, 1-7/8" OD, 1/16" Width (Pack of 25) https://www.amazon.com/gp/product/B000FMYO6Y/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 023 Silicone O-Ring, 70A...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of an adjustable...

For example, mine had red, black, and green wires (which are used for 3.3v, ground, and signal respectively).Step 5Test the endstop with the board plugged into your Octoprint board. If the LED is ON before you insert the filament, the metal switch...

&nbsp;Try not to apply too much pressure, you don't need it, too much pressure might result in the cutter coming away from your straight edge.Things you need.60mm x 19mm x 0.6mm utility knife blade.3 x M3x16mm cap head screws.3 x M3...

…the corner pieces didn't print nicely enough for mine to perfectly assemble. (maybe that's my tuning issue, orientation, or lack of supports)--------------------everything below this line is copied from original that this is a remix of- full credit...

Depending on where you decide to mount your safety/fire select switch you may need to also cut away parts of the side of the gearbox, see the pictures to see the chunk I took out of the side of mine in order to mount the safety switch through the...

Plug options include a 5-15 15 amp straight blade plug for use with 120V explosion proof outlets, a 5-20 20 amp straight blade plug for use with 120V explosion proof outlets, or a 6-20 20 amp straight blade plug for use with 220-240V explosion proof...

One part of the railway was the coal (lignite) and briquette transport from nearby mines to the town to feed the steam engines mainly in cloth factories. There were about 70 of these wagons and trains could carry up to 15 to 20 wagons according the...

... gone well and you have a piece of furniture of which you can be justly proud.   I am certainly very happy with mine!There is a lot of documentation here, and I'd really appreciate any feedback on anything that's not clear or in need of correction.

I printed mine in PLA with 7% infill, 2 perimeters, and 0.2 mm layer height. The filament I used was scavenged from a dumpster.</p><p><strong>Assembly Notes</strong></p><p>In general, there's only one way for pieces to fit together, so it should be...

Mine just needed the supports to be removed and worked fine. To start, install the M3 nuts into the base, there are 10 pockets (see 1st pic) and I added a small drop of glue (clear Gorilla Glue) to each pocket, then pushed the M3 nut into the pocket...

Mine fit fine, but I did cycle it a couple dozen times in the channel before assembling it. <ul> <li>Also verify that the small notch that the spring retainer will lock into (in the door), is free of support material. </li> <li>To assemble the latch,...

When you don't use an exhaust system like mine, this is how 99%+ of the fumes enter your work area. The cover is pretty well sealed, very little fumes will escape from there. Also when the the two cooling fans are on, (along with the exhaust fan...

... if you get that far before I do and I'll update it here. Also, thanks to Tximy. Hole sizing and spacing from this design for the wheels/Eccentric nut saved me from having to fully dismantle mine. ... https://www.thingiverse.com/thing:3343882

No special settings except for the optional color change.I suggest setting also the infill and supports angles to 35 degrees so it matches the angle of the parts.If you also want to print the letters on the cover you can use the MMU2 (or equivalent...

Its fuel trailer and Inferno Gun gave the tank the name of flame thrower tank, clearing mine areas and making them safer for passage.The 3D printable Flamethrower Tank is showcased with its fearful gun in forward position. The model’s replica has all...

This light is designed for heavy duty use in demanding conditions including emergency services, mining, construction, marine, and industrial operations where durability and reliability is critical.This portable LED light is comprised of two...

After having a blade guard break on mine while it was in my backpack during some pretty typical traveling I figured it was time to just print up a case.The main idea behind this case is to support the drone by its corners and provide rigid top and...

:) I included the modified STLs I used to make mine, basically smaller versions of DIY-Machines version and more of them and I added separate diffusers instead of his multi-filament versions, so that they can be printed on my smaller single-color 3D...

Mine are 25mm, for example, the Cross Country Performance kit uses 30mm thick spacers so you could modify the height in the Z-Axis in your slicer to potentially get 2.5" of lift from the tophat spacers alone. The lift given by the thickness of the...

therefore I've made it public. Print SettingsPrinter Brand: UltimakerPrinter: Ultimaker 2Rafts: YesSupports: YesResolution: 0.2Infill: 15%Notes:All parts fit within a 200x200x200 print volume, and I'm sure you can scale it larger, but probably not...

Or just work it out without my files.Pull the pins out of the battery connector and swap them around if they need it, mine needed it, and if you get it wrong it will fry your controller. Red to the pin on the board near the +. Only you are sure you...

If your "normal" Nanos are like mine, I needed to install different driver for my windows but also select the (old) bootloader in the arduino IDE. The same way, i felt the USB port where you connect it to the computer must have enough "Amps" to...

I am using the Asus Tinkerboard inside mine: https://www.asus.com/us/Single-Board-Computer/Tinker-Board/ Powerful board that fits where an RPi3 fits! Inside this the screen bezel is changed to hold the new LCD unit and the Pi has been moved to the...

Also, I would not recommend doing this mod without also having some compatible corner braces, like mine (https://www.thingiverse.com/thing:2474583), that will transfer twisting moments on the uprights into the horizontals, because otherwise I think...