wiccan tree topper 3d models

Topper Homero

1/2" EMT 10 and 12 hold Pixel Tree Topper. This is used to hold LED Strips for mini/mega pixel trees. The design allows for the topper to slide on the pole, but is very snug. ... You use a screw/nut to tighten the topper to the poll

3/4" EMT 10 and 12 hold Pixel Tree Topper. This is used to hold LED Strips for mini/mega pixel trees. The design allows for the topper to slide on the pole, but is very snug. ...You use a screw/nut to tighten the topper to the poll

3/4" EMT 10 and 12 hold Pixel Tree Topper. This is used to hold LED Strips for mini/mega pixel trees. The design allows for the topper to slide on the pole, but is very snug. ...You use a screw/nut to tighten the topper to the poll

1/2" EMT 10 and 12 hold Pixel Tree Topper. This is used to hold LED Strips for mini/mega pixel trees. The design allows for the topper to slide on the pole, but is very snug. ... You use a screw/nut to tighten the topper to the poll

This unit measures 1.9 times its original size, boasting a prominent star at the center. Its sturdy peg measures 15mm in length, 5.25mm in width, and 6mm in height. ...The entire structure reaches an impressive 106mm in height.

Print 2x and glued together

I designed this to allow for putting a medium size bulb (mine is 27mm at the widest) inside to light up the star. You could also add the bottom point, just be aware that the bottom hole is slightly larger than all the others. I originally tried...

Festive Finishing Touch - Elegant Apex Adorns Christmas Evergreen Emblem

i hope you like it! ...

Create a festive decoration using RGB self-changing LEDs by cutting parts from a 5mm acrylic sheet using a dxf file and a laser cutter. Assemble the star with five M3x20mm screws and mount it with two M3x16mm screws. Sand the top layer with 80 grit...

<p>Print the 20-sided core, 19 tetrahedrons and one foot. Spray in Gold. ...Use superglue to assemble.</p><p>5% infill or less recommended except for the foot (15%) there.</p>

Adjust your slicer settings to match your printer's bed dimensions, which are 330 by 330 millimeters square.

<p>I couldn't find a basic star with clean flat faces so I modeled one for myself. I recommend printing it upright with zero bottom layers (to make the hole) and supports for the bottom edges of the spokes on the star. I attached an image of the...

Made from 2 pieces to be mounted together with an M3 Screw. Spray paint glitter ... it's up to you. Hope you enjoy this design. ... My other thoughts ....need to make it lighter in future.

Enjoy! ...Will need to enable supports for the the face.

I printed this on a Prusa Mk3s. Layer height .2 You may or may not need supports depending on your machine. Print twice, and them glue or tape seams. I used a 16 LED neopixel ring to light from the inside. Lights are controlled via an adafruit...

In your slicer set up the initial bottom layer to 0, infill 0% and the wall line count to 2. Recommended to use brim with at least 10 line count for a better adhesion. ... I used white PLA and I put the christmas lights under it.

The star is splitted in 2 parts that need to be glued/fused together.The base can be printed without support.

Merry Xmas Everybody

My wife wanted a start that fit in with the theme of the stars you see below:Designed to fit this light:https://www.amazon.com/Accessory-Cord-One-Light-Bulb/dp/B07W726LD5?th=1The base should print nicely without support but the insert will need them...

A friend asked me to remix this and add an extra cone, so I did just that. ...To get the desired result, I printed it at double scale, and I'll post it online once it's complete.

I replaced the hooty face with this one https://www.thingiverse.com/thing:4744918 and scaled it to fit nicely then sliced it into more easily printable parts, optimised to only need supports on the house section

I really liked this basic design but wanted to be able to print it in two sections, needed to hollow out the base, and insert alignment holes for the parts. I used Blender to make these modifications. The holes are designed to accept a small piece of...

I created my own basic star model with clean flat faces since I couldn't find one already available. To achieve optimal results, I suggest printing the design upright and omitting bottom layers entirely - this is essential for creating a hole in the...

Remixed to use the tabs added by Captain4W for glue up surfaces but removed the bottom tab and the center support to make room for an LED light strip. I also scaled up the Inner Star to 120%. Need to print (2x) "InsideStar" and (2x) "Outside Star". I...

Here is a custom version of http://www.thingiverse.com/thing:1159436. Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1159436. ... **Instructions** Using the following options: Target Diameter Set to 100 mm Sharpness...