white empty room 3d models

I found a lot of nice designs online, but almost all of them relayed on you printing models in white and then paining them with the colors you like. I have also designed all parts to have 0.3mm fit offset so that you don't have to use XY Size...

You'll want the hotend at the bottom with the shortened PTFE tube sticking up into the white filament guide above. Then the large gear above it and the printed short handle on the side. Use the 20 mm M3 bolt, spring and washer to secure the...

In the pictures with two benchies, the black one is off of the belt printer whereas the white one is from a CR-6 SE as a comparison point.NoteThis is still a work in progress and you will most definitely find issues. Currently, I've identified a...

Once the correct amount is placed (making sure you can still mount the motor), you can fix it by gently dropping some epoxy over it.You'll also need 8 pcs of neodymium magnets for the cabin/lid.8 mm diameter 3 mm thick, like these...

These are needed on walls only as mentioned above.Attention: For the “front” part it is important to perform 2 color changes:From 0 to 1.2mm height the color is black or whatever darker color you like to use.From 1.2mm to 2.4mm height the color is...

If you have trouble getting the wire through, feed through the white pull wire, strip the end and solder it to the red and black wire. Use that to pull the red and black wire through, then cut off the pull wire.</p><p>Loop the red and black wire back...

You'll want the hotend at the bottom with the shortened PTFE tube sticking up into the white filament guide above. Then the large gear above it and the printed short handle on the side.Use the 20 mm M3 bolt, spring and washer to secure the printed...

You'll want the hotend at the bottom with the shortened PTFE tube sticking up into the white filament guide above. Then the large gear above it and the printed short handle on the side.Use the 20 mm M3 bolt, spring and washer to secure the printed...

If you have trouble getting the wire through, feed through the white pull wire, strip the end and solder it to the red and black wire. Use that to pull the red and black wire through, then cut off the pull wire.</p><p>Loop the red and black wire back...

Shorter lenses give stronger magnification and longer lenses give weaker magnification.To remove the lens from the tube, looking from the bottom of the tube, use pliers to pull downwards on the head of the 50mm locking screw, which will retract the...

If their mounting points are unmovable, the bed will have no room to expand to the sides, and it will be forced to bow (either upwards or downwards). The V-Core 3 bed plate is not rigidly connected to the machine's frame. Instead, 3 steel balls...

Its not fair that the deaf must wear face shields when we know they are ineffective on their own in enclosed rooms. They need a filtered clear reliable solution that anyone can wear. #ClearMasksForAll V2 is the culmination of months of testing...

There is a lot of room in the box for the spool box to add some extra parts…&nbsp;Optional: extrasxtra_bearing_replacement.stl: if you don't have (all) the needed bearings laying around, you can use these printed replacements.xtra_crappyfeet1.stl:...

If you prefer to use T8-8 threaded rods there is room for 60 tooth pulleys (3:1 ratio) but larger belts would also be needed. The pillow blocks holding the threaded rods have spacer blocks that are independent from the stepper motor mounts. The...

IMPORTANT: make sure you get the eye join someplace where you'll have enough room for both tails, but also where it won't risk interfering with the printer's arms. I chose to mount mine pretty close to the top of its side, since the arms can only...

This hole is not necessary if the dry box is not used, but since there is no room in the height of the enclosure, some kind of device will be needed if the filament is to be placed...

It Works, I have test it!FeaturesSecured BaseFor me, the most valuable feature is the low profile “Dock” attachment, It properly secures the controller to the table so there is no need to hold it.Four holes to secure itPush in to click-lockPush down...

* On each of the 5015 fans: * File down the top screw channel so there is room to accommodate a nut between the screw channel and the body of the BMG. The side that needs to be filed is different per fan; file one side on one fan, and the other side...

The most critical part however will continue remain ultra-high-resolution image recording along frame per second performance due constant need under surveillance for fast moving images in any condition and always high-stability data acquisition in M4...

Until I go to a flying extruder or remote-drive setup, I'm constrained to a perimeter speed of about 35mm/s at .2 layer height before filament flow through my long, long bowden becomes an issue, but I'm now running travels at 300mm/s at 6000mm/s^2...

If their mounting points are unmovable, the bed will have no room to expand to the sides, and it will be forced to bow (either upwards or downwards). The V-Core 3 bed plate is not rigidly connected to the machine's frame. Instead, 3 steel balls...

Inside this the screen bezel is changed to hold the new LCD unit and the Pi has been moved to the left to make room for HDMI wiring. Due to space constraints I am removing the HDMI port from the screen to replace it with a 20 pin .5mm pitch FFC...

They accommodate 3-4.3mm fork connectors.The blocks position can be adjusted on one axis, depending where you need room for wiring. I also modelled a press-fit stack connector, so you can mount one terminal on top, and offset, another.</p><figure...

 I'm sure there is room for improvement but as it is, it is not in terrible shape.I posted my latest Fusion360 model with the latest parts in the Fusion 360 model with the rev4 suffix.I did a quick measurement by ear with a metronome of a video of...

The servo spindle should be towards the middle of the robot.COGCut the servo horn with a pair of wire cutters so that it fits into the cogPush the servo Horn onto the cogMake sure the servo is at the minimum rotation position (turn it clockwise until...

On my machine, for some reason a couple of the mounting studs for the plate itself had doubled-up washers, and on the other plate, it had extra washers under one of the clear plastic spacers that makes room for the foam screen. So, consider checking...

Hang these from a shelf on a bookshelf, or any lip where there is room for them.MPH wallmount (tape)MPH wallmount (screws)(5mm)These modules are permanently mounted to a flat and vertical surface, also known as a “wall”. Anywhere on a wall you might...

The 3D printing model's chosen scale is 1:60 for the FFF/FDM version and 1:120 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 9 parts;- The model's very first low-poly version released in 2014.FFF/FDM...

If you want to support my work, you can contribute with me here: Other astronomical objects Object Scale [1:x] K = 103 (thousand)M = 106 (million)G = 109 (billion) Image Inner Solar System Mercury 20M, 60M, 120M Venus 60M,...

If you want to support my work, you can contribute with me here: Other astronomical objects Object Scale [1:x] K = 103 (thousand)M = 106 (million)G = 109 (billion) Image Inner Solar System Mercury 20M, 60M, 120M Venus 60M,...