what size nozzle comes with ender 3 3d models

A remix of FONSWERKS' 25mm feet for the Ender 3 V2, using T-nuts to fix the feet to the frame rather than printed inserts sliding into the rails. No hassle making sure the rail inserts are printed not too loose or too tight, with Tnuts it just...

Works best together with https://www.thingiverse.com/thing:3095575 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.1-0.2 Infill: 15-20% Filament: Filament-PM Best with PETG or similar, PLA would creep and...

For those with trouble slicing the base model (it has some defects but works fine in Cura) or if you want to print it without supports for the teeth, alessi71 remixed the main part here: https://www.thingiverse.com/thing:3218716 I included it here...

This is a custom cover for the stock Ender 3 power supply that adds a USB socket to power a Raspberry Pi running OctoPrint. It also includes a divider between the mains AC section and the low voltage DC section of the cover, as well as a mount for...

This remix is for a direct drive Ender 3 (Pro/V2) to use the system as reverse bowden setup with the aperture science logo. you will need a standard 4mm outerdiameter bowden tube, that feeds into the inlet of your extruder. you also need a new...

During a routine inspection of my Ender 3, I noticed that the filament had ground a sharp edge in the extruder hole on the E step motor; even though I upgraded to an aluminum extruder. I designed this part to guide the filament into the extruder...

I chose to use the aluminum extruder tensioner bar, but the standard one should work just as well on any Creality printer that uses the same setup as the Ender 3. So far, I've had success printing with NinjaFlex (85A) without a single jam, so it's...

As many users have discovered, adding a knob for the Ender 3 extruder is an excellent upgrade. However, it can become easily stripped if not secured properly. Frustrated with repeatedly printing new knobs, I designed this adapter to attach to the...

Printed and tested on an Ender 3 using Simplify3D without any problems at all - it works great! Note: This is just one part of a set; you'll still need the other two pieces from the link above to complete the design. Note 2: I used 0.4mm for...

This is a straightforward spool holder for the Ender 3. I never found the stock spool holder's friction levels to be satisfactory. This uncomplicated mod incorporates bearings, allowing the spool to rotate effortlessly. If you're like me and don't...

Here is a pen holder to install on an ender 3 handy it installs and uninstalls in a few seconds it and clip and the inside contains likes that mine holds well in place. ... requires a m5 /20mm screw and a nut as well as 4aiment of 5mm diameter and 1mm...

This is basically the exact same model, except the bottom drawer is less wide to leave room for airflow into the the electronics (there are some openings on the right side of my ender 3's control box probably for air to get in and i didn't want to...

Improved Blowing for Creality Ender 3. Sorry About My Curve English. To Use This Blowing, You Need to Raise the Extruder Cover by Eleven Millimeters. ... Note: For Optimal Performance, Make Sure the Left Ear of the Cover Locks into the Bolt on the Top...

This a mount to convert your Ender 3 V2 to Direct Drive. It allows the stock fan shroud to remain and has a mount for the BLTouch. ...It mounts the stepper sideways so that it clears the Z Extrusion so that no printing area is lost

Ender 3 mainboard cover, stock screws to move the mainboard cooling fan over the stepper motor drivers/heatsinks and make some room for the BLtouch pin 27 board. ## Updates ### 5/26/2019 * Mainboard screw holes updated to accept stock fan screws...

All you need is 2 x 608ZZ Bearings I printed this in my ender 3 pro, with 0.2 layer height with 7% to 10% infill but that depends on your pattern and the strength you looking for. I printed my nut with 0.3 tolerance, and it gets on it with a litle...

I really like look and the design of the "Ugly-but-Light" Fan Duct upgrade for the Ender 3 v2. However it was missing some of the things I was wanting. changes made are listed below. 1. added support for the Sonic pad senser. 2. Uses standard...

This is a remix of a good design, but I have added a diode (3 mm, red, 2V, 20 mA) with 510 ohm resistor powered by the same converter as the fan (12V) and the LED is in the eye of Ender dragon which I have added to the front face of this cover. I...

This is an edited version of All in one Ender 3 case for MKS or SKR v1.3. I removed the original fan and placed a fan on both lids. I know it doesn't look perfect, but I found it the easiest way to design if you want to achieve better cooling...

I do not take any responsibility for harming or destroying yourself or your 3D printer during installing this mod. 7.10.2020 Removed mounting holes on the top. Added Fusion360 file. 7.9.2020 PSU cover with mounts for any 120mm fan using stock...

It was not easy to get all these features into firmware at the same time due to the small flash size on the Ender 3. To achieve this, I had to add compiler optimization parameters to the file "Arduino\hardware\arduino\avr\platform.txt": ...

so if you need to shift things around or adjust tolerances, it makes your life easier You Must Print Everything Labeled BTT if you are using a TFT 35 Credits: Drawer: Remixed From: Ender 3 full PCB cover with drawers...

Here is a modified filament guide for Creality printers such as the Ender 3. After printing a few times, I noticed wear on some parts due to filament friction. This modification redirects the filament directly into the extruder hole, reducing...

Still in development, This is a remix of my remix of Ender 3 SD Card Extender Front Mount by skydog538 My original was designed for a MicroSD slot; this one is tailored for an SD slot. The file also includes just the SD adapter Box to print and...

This remix is for a direct drive Ender 3 (Pro/V2) to use the system as reverse bowden setup. you will need a standard 4mm outerdiamtede bowden tube, that feeds into the inlet of your extruder. you also need a new filament spool holder, that sits on...

I took Holspeed's Ender 3 Tray and integrated a raspberry case to house your OctoPi, adding a crucial hole in the back for an XT60 connector. Next, I utilized an XT60 splitter to tap into the printer's power source, stepping down 24V to a reliable 5V...

This is a Spoolholder with integrated Scale and LCD for Ender 3. The Spoolholder can easily detach from the Profile at any time. A simple 5kg Load Cell powers the Scale, which is connected to a user-friendly Nokia 5110 Display and an Arduino nano...

Super over engineered extruder plate for printing TPU on Bowden (stock 2/4 mm ID/OD tube) Ender 3/3 Pro/ CR10/S/Ender 2/Ender 5 hotend. Extruder plate was merged with zip tie PTFE tube clamp to extra secure tube from falling out of coupler. I...

... too large and positioned incorrectly for my needs. ... Thanks to @submano for sharing their idea and original concept, which served as inspiration for me to recreate it with my own modifications. Printed in PLA without any issues with the hot nozzle.

This is a simple modification that changes around the hotend configuration of the Ender 3 or any printer using the same hotend mount. The 40mm hotend fan is replaced with a 30mm fan and the metal housing is replaced with a printed duct. The bowden...