what filament for ender 3 pro 3d models

I made this filament filter to be used in conjunction with side mounted filament.

This filament guide will properly feed filament to the extruder. ...This will also help smooth pulling of filament from the spool.

A filament cleaner that can be directly attached to the extruder.

Mounted securely onto the Z lead screw, this filament guide offers unparalleled protection for your valuable plastic extruder. Whether you're an experienced maker or a hobbyist, this essential tool will shield your machine from costly damage caused...

I was having problems holding my almost empty filament roles on the spool holder so I made this. used pla at .24 layer Hight with a 15% infill one suggestion I have if you make this is to wrap duck tape or electrical tape around it once to grip...

... which was prone to snapping off during use. ...To prevent this, I reinforced it for added durability. I also opted for a 100% infill print, but in reality, you might be able to get by with a lower percentage and still achieve satisfactory results.

This is a custom mount designed specifically for the Bigtreetech smart filament sensor on an Ender 3 Pro that features a dual gear extruder. ...This creation replaces the bottom portion of the BTT sensor housing, which can be viewed in detail at...

Here is all my Side Mounted Spool Holder Ender 3 Pro whole setup after a few tests, and this is what worked best for me: Spool Holder: https://www.thingiverse.com/thing:3646853 The spool holder diameter is 2 or 3 mm smaller than the Ender 3 Pro...

Support for filament sensor and ventilation in Ender 3 PRO extruder. I added the extra ventilation to avoid that, if there is a lot of retraction, the filament gets hot and breaks, especially in summer it happened to me a lot. The fan is in...

For what regards the assembly, is not complicated and the required parts are (referring to a Creality Ender 3 Pro machine): - 1 additional bowden coupling of the M10 size; - 1 additional piece of bowden of more or less 60mm (59.5mm worked for me); -...

This is a custom remix of a combination cable guide/filament guide designed for the Ender 3 Pro, specifically tailored to work seamlessly with the EZR Studer by SeeMeCNC. The original design was adapted to fit perfectly on the extruder mount using...

The design was based on the work of ArdyJay "Filament guide for CR-10S, Ender-3, Alfawise U20, etc." I just made it solid and add the hole for PTFE Tube to make sure the filament won't shave again. I recommend to print using PETG, because i tried...

Beslag til Filament Holder, Ender 3, Ender 3 Pro m.m.

I made my own filament guide for Ender 3 v2 / Pro, the ones I found online were always needing extra parts that I didn't want to buy and this one fits perfectly and works like a charm without needing anything else than the two original screws that...

This is a remix of https://www.thingiverse.com/thing:2770487: a combination cable guide/filament guide for the Ender 3 Pro, compatible with the EZR Studer by SeeMeCNC. It mounts with the Z-rod screws on the extruder mount. For whatever reason the...

Feel free to tip if you want to support 👍 https://paypal.me/adrienpvm I made my own filament guide for Ender 3 v2 / Pro, the ones I found online were always needing extra parts that I didn't want to buy and this one fits perfectly and works like a...

I recently upgraded my Ender 3 pro with BLTouch and Filament Sensor, so i needed a simple filament sensor mount. So i designed it.Parts needed:M3 x 20 screw 2pcsM3 x 10 screw 1pcs (Optional)M3 insert nuts 3pcs (or 2)5201 bearing ('Cause I had an...

Really liked the simplicity and effectiveness of Filboyt's 2020 / Ender 3 filament arm, but its clip wouldn't fit the top end rail of my CR-10S Pro without modification due to screw placements for the Z-Axis threaded rod end support, and after...

This remix is specifically tailored for the Ender 3 Pro, a printer purchased in May 2020, based on the Syntaxcuemi3D design for a side-mounted spool holder. Careful attention was given to aligning the extruder, as it was initially too low for...

Hello people, in this project I have installed the E3D Hemera Hotend on a Creality CR-20 Pro / Ender 3. In addition, the x-axis was upgraded with a Linear Rail System. Furthermore the BLTouch of the system was moved accordingly. As a filament...

He did not make the bolt part that would fit my Ender 5 Pro. This one will do that. I am thinking this will fit the Ender 5 as well as they are basically the same frame. So use his roller and the holder along with the Creality nut he designed and...

This part is specifically designed for attaching the stock filament runout sensor of Longer LK4 Pro to a dual drive extruder upgrade kit.\r\n\r\nThe upgraded aluminum dual-gear pulley dual-drive extruder kit can be found here:...

This uses the stock ender 3/ender 3 pro spool holder bracket and is meant to turn the spool so that it goes straight down into a direct drive hot end.Additional Hardware:1 x m5 nutPrinting:Printed in PLA. Print in the orientation as shown in the CURA...

Hello people, in this project I have installed the E3D Hemera Hotend on a Creality CR-20 Pro / Ender 3. In addition, the x-axis was upgraded with a Linear Rail System. ...Furthermore the BLTouch of the system was moved accordingly. As a filament sensor,...

Remixed from https://www.thingiverse.com/thing:4821339 Loved the design, but I had no need for the Z axis guide. ...I used this on an Ender 3 Pro, not a V2, so I removed the text as well. ...Prints easily with no supports required.

I designed this Filament guide for my Ender 3 V2 to make it easier to load filaments. I upgraded to dual geared extruder many months ago, however it was not particularly easy to thread the filament through the tiny hole and often the filament would...

This is a remix of two different filament sensors to make installing the sensor on your Ender 3 / Ender 3 Pro / Ender 3 V2 very easy. Instructions: 1. Use the stock screws that come with the stock z-endstop to install the switch to this mount...

A simple dust filter that fits on Ender 2 pro Z axis lead scre spindle mount. I filled it with a piece of sponge and works very well. ...The design includes a cylindrical body and a M14 screw cap.</p><p>I printed it in red PLA with 0.4 nozzle at 0.2...

Upgrade is designed for Creality Ender 3 Pro and 5015 turbo fan (You may need to buy 24V or 12V version, you must check your printer specifications). Original design had a couple of issues which I have fixed. In the 3rd image, gap inside the red...

2021 when you use aluminum extruder upgrade, use my remix filament guide: https://www.thingiverse.com/thing:4778629 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.12 Infill: 20% Filament: C-Tech...