what filament for ender 3 pro 3d models

extruder filament guide for Ender 3 Pro stock screws

Filament Guide for Ender 3 s1 Pro in Cura Software Infill 80% Support Checked

Easy filament spool chim for my ender 3 pro. Fit spool with hole 53mm and over. For spool with 55mm hole a chim to fill the small gap cloud be made but work without it. Just make sure to have the filament spool support install like the first picture...

This is a revised version perfect for my Ender 3 Pro, which I purchased in August 2019. Be cautious, as older versions of the printer have the filament hole slightly offset. ...In this revision, I simply trimmed the hole for the lead screw, eliminating...

Doesn't need any other parts, very useful for loading your ender 3 pro with new filament. Very easy to install, just align the flat side on the bottom of the part with the flat side of the bowden extruder that feeds the filament to the hot end. Push...

It might be compatible with the Ender 3 "Original" edition as well as the Ender-3v2, but I cannot test it since I only own the Ender 3 Pro. I printed it in PETG, but I have no doubt that any filament material would do for this roller. ... ...

I wanted an enclosure for my Ener 3 pro to be able to better print ABS. I needed a thermal blanket but that needed support so i designed the Longarms to hold the top. The spool holder was an issue so i created a holder that would allow me to easily...

... ... Reasons for redesign: 1. Tighter fit in Ender 3 Pro top rail. (Original design was very loose on my printer.) 2. Sleeker curves on the arm. ... Last picture shows original part (link above) on top, and this redesign on the bottom.

for the screw in fittings it uses the PC4-M10 Pneumatic Fitting you can find on amazon at link...

Update: June 22, 2020 I was designing a Z rod holder (available here: https://www.thingiverse.com/thing:4493376 ) when I discovered that an old bearing from my Ender 3 Pro's wheel fits perfectly in this filament guide as well. The bearing is an 625...

This replaces the default spool holder tube/shaft that came with the Creality Ender 3 Pro, specifically designed for use with a Hatchbox PLA 1.75mm Filament spool. There are three parts to print; the Spool Shaft, Hex Nut and Locking Ring. Print...

I have added a base so that it can be mounted on the right rail of the Ender 3 Pro. I have raised the lower magnet so that it is stronger and changed the size of the magnets to 10x10x2mm. I have attached a box which functions as a collection...

You'll also need to print the following files: - "01_main_arm" (1 unit) - "02_sec_arm" (1 unit) - "03_wheel" (3 units) - "04_wheel_shaft" (4 units) - use 100% infill for optimal results Optional components include: - "05_wheel_cover" (3 units) Don't...

I wanted an enclosure for my Ener 3 pro to print ABS with greater ease. I required a thermal blanket, but it needed additional support, so I designed the Longarms to hold it in place. The spool holder posed a challenge, so I created a holder that...

Filament guide for up. V2 - nuts. ...V1 - binder clip.

I created in Tinkercad a superior Roller Guide for smoother filament roll handling, specifically tailored for Geetech 2019 models. Although still a work-in-progress, this design promises better performance than the standard stock holder. ...Its primary...

Filament guide. ... Things included in the design: - Reduce the material required, whilst still being functional - Push fit so no other parts required Supports are required for the locating tabs.

I made this spacer because I could not find one that fit the spool on my printer arm. ...This has a larger hole to slide over the spool on the printer. I also made it a bit long so there is not a lot of side to side movement of the role of filament.

The new model is significantly smaller and boasts less complexity compared to its predecessor, making it an ideal choice for everyday use.

... This is a mix of two dust filter ideas: https://www.printables.com/model/262818-filament-dust-filter-for-ender-2-pro https://www.thingiverse.com/thing:190118 Print Settings Printer: Ender 2 Pro Rafts: No Supports: No Resolution: 0.1 mm Infill: 100%

I'm excited to share with you a remix of the Ender 3 Filament Guide by MattEllison that I've extensively modified to accommodate longer prints and provide an extended filament guide arm. By positioning my filament on the side of the printer, I've...

Filament Guide for Ender 3, 3-Pro or V2 - uses wide pulley to minimize bending stress on filament. Clings to the Z-Axis Roller Spacer and Extruder Plate. ...You have options to use a plain pulley or a ball-bearing supported pulley.

Works fine for the Ender 3 Pro and prevents the filament spool from falling off the printer.

Ender 3 Pro Filament Guide

ender 3 pro filament guide

Ender 3 Pro Filament Guide

Filament guide for Ender 3 PRO with logo and filter

A steady and simple filament guide for Creality standard and upgraded extruder. Especially on the upgraded aluminum extruder it can protect filament from being scratched by the sharp corners. ...

Filament guide support designed to be very resistant.

I liked Filboyt's design but mine kept working loose. ...Just need a couple screws and t nuts to attach top and bottom. Been using for 6 months and they dont move.