west elm arch mirror 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

I've included the 3 I've made to start and this entire design is easily mirrored in your slicer if you need the opposite hand. Two are designed to mount to 20mm extrusion (left and right) and the other is a flat base that MUST BE SCREWED DOWN or it...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 height = 15 shape =...

If you haven't flipped your Z-assembly on the right, then you can mirror the file for the front left switch in your slicer. Mount the parts to the Z extrusions with M3 12mm button head bolts (counter sunk because most people will have a few 12mm...

Check the following pictures.Now put it into the table and add spools you want to have thereIt holds up to 7 spools on one side, now I'm printing suplik1,2,3 again for the second side (they are mirrored so no adjustments needed). If you like the...

Do NOT use Eco-PLA Mirrored left/right side bases allow your controller to swing out of the way when desired. Strong Rare-Earth magnets hold your controller in place when in use. 2 Variants of each base, one with built in hinge core spacer, or...

Body Clamp - This adds a set of mounting points that mirrors the front-sides of the Multibase but is independent of the Rack Rod. It clamps to the body casting and spline on top. I have not uploaded any parts that use the front mounting points. The...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

I have also added plastic M5 spacers from 1mm to 4mm in height if you need them to shim up for M5 screws that might be a little too long, **8x_M5x1mmSpacers.stl, 8x_M5x2mmSpacers.stl, 8x_M5x3mmSpacers.stl, 8x_M5x4mmSpacers.stl** There is also a...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Also, these prints are mirrored STLs combined into one model. So you may see two entities in a single STL. Most slicers will automatically merge adjacent STLs for printing, but yours may not, so look out for that. Cura has no issue with these...

It's not strictly necessary, but if you want to make sure the holes are aligned you should mirror 2 of them. If you have a new style of bed for the snapmaker (the design has been revised) it should be possible to replace that stl to generate a...

The result is a lifelike virtual representation that mirrors the visual qualities of the real-world croissant, enhancing the overall dining experience for patrons in augmented reality settings. The Croissant Norweski, also known as the Norwegian...

Snow White, the lead character from a 19th-century German fairy tale "Snow White". The fairy tale features such elements as the magic mirror, the poisoned apple, the glass coffin, and the characters of the Evil Queen and the Seven Dwarfs. No supports...

The box closes by twisting the upper collar anti-clockwise (this can be reversed by mirroring the object in your slicer) while holding the base stationary. To loosen it up initially, I twist on the box firmly, and then pull each of the doors upwards...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

This is a mirror/flip of the good side and should fix the problem of hitting the arms in the back. Also updated both v2 braces. You'll want to lay them flat for printing. Once I know they work, I'll do that. -- <strong>Spring hits on the front now. ...

Body 7020motors.3mf for 7x20mm coreless motors Cover: racingCover.stl or MINIFIG-Cover.stl 2 @Nozzles: 8520 nozzle.3mf or 7020 nozzle.3mf depending wich motors you use 2 @Propellers: propeller.stl 2 Shaft joints: Joint.stl @ = the nozzles and...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: shape =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

You can use other sized bolts (M3 or M4) files are uploaded for adjustments, I can and will upload different sized models.* *OPTIONAL PARTS* 3x WASHERS (desired size) 3x Nyloc Nuts (desired size) #HOW TO PRINT During the design process I accidently...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 74 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = 1.6 shape =...

(http://www.thingiverse.com/apps/customizer/run?thing_id=116042) Instructions: Using the following options: - Mirror: Yes - Height: 15 - Shape: [[[-30.607849, -48.473831], [-38.714745, -48.950043], [-40.559818, -48.486679], [-42.201851, -47.493645],...

You can really crank these out quickly! I recommend printing a second set of the tiles mirrored so you get more variation. I find it best to force the bridging angle to 45 for these parts. The slicer I use will try and choose the best bridging...

If you want a complete pair, make sure you mirror this piece or else you'll have two lefts or two rights. Outboard pieces have all through holes, with one nut inset. There's no reason to have 3 super long screws, when two will suffice. The old...