wemos 3d models

I searched all over Thingiverse for a WeMos D1 Mini case to fit my needs, and couldn't find one. So here it is, a tight fitting case, that also has brackets for wall mounting the device. Currently work in progress until I get a perfect fit. ... If you...

Wemos D1 OLED ESP12F OLED Case with Built-In Reset and Flash Buttons. 0.4mm Nozzle. Layer Height: 0.2mm or Less. Note: Ensure your printer's X/Y axis and extrusion flow are well-calibrated to ensure a proper fit. If the cover doesn't fit, adjust...

This will fit the Wemos D1 Mini Pro / Relay Shield with headers mounted in the configuration in the pictures. Left a small hole to get to the reset button with a paperclip. Added a few ventilation holes in the back. Widened the opening for the...

As I had only a Wemos D1 mini lying around, I modified the case in tinkercad to be able to use my board.I used soldered on pin headers (on the opposite side of the WiFi module) and made it so there is enough area to simply glue the board in...

... was 10ish years ago. There are a few different variations of the lid. For the actual temp sensor I used tasmota firmware, ds18b20, and a wemos D1 mini. ...It connects to a hubitat, but you could use whatever firmware and connect to whatever service

I searched all over Thingiverse for a WeMos D1 Mini case to fit my needs, and couldn't find one. So here it is, a tight fitting case, that also has brackets for wall mounting the device. Currently work in progress until I get a perfect fit. ... If you...

WiFi Wemos D1 ESP8266 control box for temperature and humidity control by Supla Display cover must be tapped M3 thread ( the best way is to use screw before assembling it) In base tap M3 thread for that screw Cover should be also tapped by M3 thread...

Small box to take a Wemos D1 Mini with Power and Relay Shields. Prints in 4 parts, the main case, the Lid The 2 part cable entry will need glueing together so it slides down the hole. There are no holes in the cable entry, so you will have to...

A simple case to house your WEMOS D1 mini project. Features: * Snug fit * Reset button access * LED viewable * Will fit over posts * Cover has wire access port * USB connector fit relief * Simple to print * Cover only fits one way ...

This is a simple enclosure designed to hold a Wemos D1 Mini and the Wemos SHT30 Temperature/Humidity sensor shield securely in place.\r\n\r\nThe small baffle that comes with it effectively holds the shield to the base, reducing heat soak from the...

Additionally, I relaxed the tolerance on the Wemos board while tightening the tolerance on the sensor, making corresponding changes to the lid. If you print the lid in a translucent material, you can observe the built-in LED through it. You may need...

The code (and all other design files) are located in GitHub: https://github.com/YigalB1/Trafic_Lights_WEMOS The LEDs are placed on a small PCB designed with EasyEDA, yet with a mistake for 5mm LEDs, will be fixed later on for 8mm LEDs. Contact me...

Pi-hole Monitor is a Wemos D1 Mini (ESP8266) with an I2C OLED display that is managed through a web interface and sits on your local network and will display statistics from your Pi-hole server. This is a station box designed for the Wemos D1 Mini...

Pi-hole Monitor is a Wemos D1 Mini (ESP8266) equipped with an I2C OLED display that's managed through a web interface, sitting on your local network and displaying statistics from your Pi-hole server. This is a station box designed for the Wemos D1...

But, I found that it looks like there have been some minor revisions, or maybe just different manufactures, to the Wemos Mini D1 boards since he created his... I made the following modifications to his original design: * I've widened the groove...

Wemos D1 mini Work Table holder - V2.0 Print Settings Printer Brand: Anycubic Printer: Kossel Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: REGSHARE PLA SIgnal yellow Category: Gadgets

The lid holds the Wemos Mini D1 in a slot that leaves the pins available. ...The bottom has holes so that it can be used with an environmental sensor such as the BMP180 temperature/pressure/humidity sensor pack.<br/> There is a cut out in the bottom to...

I really like the case made by WRODZ https://www.thingiverse.com/thing:2397879 but for my Wemos Wi-Fi it was missing an add on for the SMA connector and a small space for my GPS antenna. Using existing vent holes I use 3 x M3 hardware and some low...

To achieve this goal, I had envisioned using the following components: A NeoPixel ring with 16 LEDs to provide an eye-catching visual representation of audio levels The Wemos D1 mini as the brain behind the operation, handling all the necessary...

I have designed a small, handy case for the WEMOS ESP32 D1 Mini version. Board just snaps in place (start with the USB-port when inserting) You need 4 M3x6 screws to fix the lid. There are two versions of the lid: Version 1 for directly...

I used an ESP8266/Wemos D1 mini flashed with ESPHome and connected to my HomeAssistant. Cramming everything into the case is quite a challenge, but in the end it should fit. ...I glued it right beside my Desk so I can toggle multiple Automations in...

Here we have a WEMOS built into a form factor that also doubles as a desktop coaster. Along the front are 6 individual Adafruit sequin LED's that each represent an alert channel. Favourite youtuber , twitter account or Big Query result. They are...

I made this remix to be used as part of my Home Assistant Glow setup.It uses a Wemos D1 Mini v2 board with soldered on headers, the “Lid” model has extra height to allow for the connectors to fit and then wires to pass through the lid.I've also added...

This is a remix of SuperCub's AirCare - Temperature and humidity with Wemos D1 Mini and DHT22 https://www.thingiverse.com/thing:4691909 Things I changed: -Made it longer since the DHT module I'm using included the board -Raised up the little nub at...

... and using it as an extended button. To assemble the housing, print both halves flat, place the Wemos inside, and then glue them together. ...I used acetone to melt the halves into a single piece, but superglue can also be used for this purpose.

A case to hold a 12 Led NeoPixel Ring (AliExpress and not the real one from adafruit) and a Wemos D1 (ESP8266). The size of the 12 Led NeoPixel Ring is inner diameter 48 mm, outer diameter 56 mm and this is larger than the official Adafruit one.

... player need to be added. This latest version of the Wemos holder has been revised by Wonderphone creators to accommodate a German T65 Telephone or FeTAp 61. ... As of October 30th, 2019, an update was made to secure a tighter fit for the DF-Player.

Files are compiled for printing a charming little enclosure for the WeMos D1 Mini development board, designed specifically for the ESP8266, along with the OLED shield. This is part of an instructional video for constructing a compact desktop display:...

I really like the case made by WRODZ https://www.thingiverse.com/thing:2397879 but for my Wemos Wi-Fi it was missing an add on for the SMA connector and a small space for my GPS antenna. Using existing vent holes I use 3 x M3 hardware and some low...

This is a compact casing that snugly fits a Wemos NodeMCU 8266, an AM2302 temperature sensor and a VMA314 PIR sensor in one neat package. It assembles effortlessly, requiring only a few quick soldering steps to join the components together, then...