wemos lolin32 3d models

This design works well with the latest stable build of espeasy mega: Connect the PIR to the 5V/GND of the wemos and the data wire to D0. Then add a device in espeasy using D0 (GPIO-16) as a normal switch (switch input) and bob's your uncle! D0 is...

The holes for the LEDs on top and the space for the Wemos at the bottom are very precise because I didn't want to use glue to secure the LEDs and board. As a result, you'll need to press firmly when inserting the LEDs and Wemos. In "Thing Files," you...

Mine is an aliexpress bought relay. I added terminal protection and a cover for where you need to screw the terminals as I intend to use this to switch 240v. Btw yes I know in the image of the relay and wemos the wemos isn't soldered to the headers,...

UPDATE: Added a "Rugged" version with clips (pretty flimsy, take care) for an increased holding strength. A very slim case for the WeMos D1 Mini DISCLAIMER: I've designed this case to fit my WeMos board with very small tolerances. I hope it will fit...

This design iteration showcases a casing that can house multi clamps, a 220V-12V transformer (I'm using 1A USB power connectors for this purpose), a single-channel relay and a WEMOS D1 mini board (potentially a NodMCU). The design is straightforward,...

For reference, check out https://www.banggood.com/Wemos-ESP32-OLED-Module-For-Arduino-ESP32-OLED-WiFi-Modules-Bluetooth-Dual-ESP-32-p-1181297.html. It features a sliding top mechanism that may require some finesse to insert, depending on the...

This is one design iteration for a casing that can house various multi-clamp setups, a 220V-to-12V transformer (I'm utilizing 1A USB power connectors for this), a single-channel relay, and a WEMOS D1 mini (possibly an NodMCU) \nThe design is...

I'm gradually integrating intelligent devices into my household, starting with one that can accommodate a Wemos D1 mini and a DHT22 sensor. The design is straightforward, eschewing elaborate mounts or screw placements since I'm working with existing...

Minimalistic holder with legs for Wemos D1 mini on the back of the MAX7219 display - clamps simply slides to the MAX7219 PCB. I also uploaded FreeCAD files so you can adjust measures if needed. My ESP8266 clock also has two sensors - LDR for...

This is a preliminary design concept for a versatile enclosure that can house multiple clamp assemblies, a 220V to 12V adapter (powered via USB Type-A connectors with 1A current rating), a single-channel relay module, and a WEMOS D1 mini...

... in the chuck and then hold the head up against a grinder until it's small enough. It's worth noting that this screw can have sharp edges, so be sure to smooth them out with sandpaper before inserting it into the Wemos to avoid damaging any leads.

This is running a tweaked version of HA-Glow Project (ESPHome) to have two pulse_meters (Energy Import/Energy Export)Please note this fits the Wemos D1 Mini v3. ...The Wemos D1 Mini v2 does not fit.I adjusted the size of the USB port to be able to fit...

Genuine Wemos modules feature USB and reset buttons below the board, while some clones have them positioned above. This holder accommodates both configurations. The included breadboard may vary in size slightly due to differences in manufacturing. A...

NOTE: Be careful when you insert the USB into Wemos, too much force and the chassis will pop out of the small slots it slides into. Future Ideas: Find a way to insert the monitors and face plate without fasteners or glue. Print instructionsI was able...

This is another sensor box built with the following components: * WeMos D1 Mini microcontroller * TEMT6000 Light Sensor for detecting light levels * AM312 PIR Motion Sensor for motion detection * BME280 Temperature, Humidity, and Barometric Pressure...

This design concept is for a housing unit that will hold several multi-position clamps, a 220V to 12V transformer (I've opted for 1A USB power connectors as a suitable interface), a single-channel relay module and a WEMOS D1 mini board...

This design iteration focuses on a case that can hold multiple clamps, a 220V to 12V converter using 1A USB power connectors, a single-channel relay, and a WEMOS D1 mini (possibly a NodeMCU). The design is straightforward, featuring no elaborate...

This model was engineered to accommodate the Wemos Lolin ESP32 OLED, and can be found on eBay at https://www.ebay.com/itm/222975245863. ... Printer: Ender 3 Pro Filament: Hatchbox PLA Orange and Black Hotend temperature: 215C Bed temperature: 60C...

This revised version builds upon the Wemos holder used by Wonderfoon parts, especially designed for Wonderfoon PCB. I designed a printed circuit board (PCB) to simplify the assembly process of Wonderfoon and minimize wiring errors, saving precious...

I needed a custom case that offered easy access to VCC and ground pins, so I designed one specifically for the Wemos D1 Mini and Relay Shield. The existing cases available were nice, but they lacked a snap-together design that would eliminate the...

The lid holds the Wemos Mini D1 in a slot that leaves the pins available. ...The bottom has a single hole for a 12mm LED button to be mounted.<br/> There is a cut out in the bottom to allow access to the USB port.<br/> The case is screwed closed with 4x...

This is a complete rework of my previous [Sensor Box for Wemos D1 Mini, 18650 battery and T/H sensor](https://www.thingiverse.com/thing:4706394). Wanted something more compact with separate bays for battery tray and electronics. Both parts are...

I'm kicking off a series of "smart" device additions to the family home, starting with one that can accommodate a Wemos D1 mini and a DHT22 sensor. The design is sleek and straightforward, eliminating the need for elaborate mounts or screw placements...

I'm designing a smart device enclosure for my family's home, incorporating various components such as multi-clamps, a 220V to 12V converter, a single-channel relay, and a WEMOS D1 mini microcontroller. This initial design is straightforward, avoiding...

This is one design concept for a case that can house multi clamps, a 220V to 12V converter (I'm utilizing 1A USB power connectors), a single channel relay and a WEMOS D1 mini (potentially a NodMCU). The design is straightforward, no complex mounts...

This is one design iteration for a housing unit that can accommodate multiple clamps, a 220V to 12V converter (I'm utilizing 1A USB power connectors for this), a single-channel relay and a WEMOS D1 mini (possibly an NodMCU). The design is...

However, in practice the light is clearly visible through the plastic. NOTE: Be careful when you insert the USB into Wemos, too much force and the chassis will pop out of the small slots it slides into. Future Ideas: Find a way to insert the monitors...

I designed it to fit the Wemos Lolin ESP32 OLED https://www.ebay.com/itm/362946345220Printer: Ender 3 ProFilament: Hatchbox PLA Orange and BlackHotend: 215CBed: 60CDesigned in TinkercadSliced it in Cura 4.5Print SettingsPrinter...

This fixture securely holds a Wemos D1 Mini in place, allowing for easy attachment via glue or by placing rubber sheets beneath it to stabilize the sensor. Alternatively, a rubber band can be applied directly to secure the sensor firmly. To mount...

A small housing for a Wemos D1 mini and a DHT11 / DHT22 to monitor temperature and humidity via Wifi. The small block is screwed to the wall, the housing could anytime be removed for e.g. re-programming. Access to the Reset-button from the...