wemos d1 mini development board 3d models

I needed a Wemos D1 Mini case that had room for some passive electrionics and an extended power harness for WS2812B LED Strips. ...Loaded the original Fusion 360 design file by Surrbradl08, modified the sketch to extend the length of the case, and...

... both control boxes to fit my Ender 3 perfectly. I even drilled a hole in the back of the case so I could pass an LCD cable through it. To-Do List: * Remix the left side to accommodate my mosfet and Wemos D1 Mini PRO with its external antenna.

Modest adjustment made to P3Hi's Wemos enclosure, eliminating excess filament within the lid to accommodate boards featuring soldered pin connectors.

Supports only needed to box unit for wemos d1 + buzzer + led.

A case for my Dual Energy monitor with Max display and Wemos D1

This is a case for a D0 Counter.I used a Wemos D1 Mini with a Phototransistor and a Resistor (1k) directly Soldered to the PCB of the Wemos D1 Mini. ...Use 1 or 2 8mm Magnets to Connect it.</p><p>I used this Thread to configure it:<br><a...

... that you print three or four button pieces together at a time, as this makes the printing process easier. Electrical wiring instructions can be found at https://spiritdude.wordpress.com/2018/02/16/wemos-d1-mini-with-i2c-ssd1306-oled-128x64/.

Reading a G4 RF1 gas meter with TCRT5000 sensor and WeMos D1 Mini. ... Fits perfectly for a G4 RF1 gas meter Please refer: https://be-jo.net/2022/02/home-assistant-gaszaehler-mit-esphome-auslesen-flashen-unter-wsl/ ...

I was tired of all those D1 mini shields cluttering my desk and drawers, so I made this little thing. It is good for up to 28 shields (in reality more like 20) standing upright in a standard hardware storage cabinet drawer. ...The dimensions of this...

I was fed up with all those D1 mini shields cluttering my desk and drawers, so I created this compact solution.\r\n\r\nIt can hold up to 28 shields (in reality more like 20) standing upright in a standard hardware storage cabinet drawer. ...The...

... ... Both Wemos D1 and Relay box should snap in place. Some filing may be required. Lid will accomodate a 0.96" oLED Display. Just drill holes to mount. ... There is a bottom version without hole if you wish to use as standard Wemos Project Box.

A small housing for a Wemos D1 mini and a DHT11 / DHT22 to monitor temperature and humidity via Wifi. The small block is screwed to the wall, the housing could anytime be removed for e.g. re-programming. Access to the Reset-button from the...

Here's a case for a D1 Mini + either a DFRobot or a HLK LD1115H mmWave sensor. It is a remix based on the original design by 'alasdairedward'. I have removed the foot and added a hole in the back that fits a ball socket and fastens with a locknut....

I designed a compact case for use with the D1 Mini and a BME280 Temperature, Humidity, and Pressure Sensor. I use it to read temperature and humidity in various locations around the house. That information is used by Home Assistant home automation...

I was tired of all those D1 mini shields cluttering my desk and drawers, so I made this little thing.It is good for up to 28 shields (in reality more like 20) standing upright in a standard hardware storage cabinet drawer. The dimensions of this rack...

Here is the guide to building the sensor: https://hassiohelp.eu/2021/03/19/esphome-creazione-multi-sensore-garage-in-home-assistant/ Case for multisensor: Wemos D1Mini + HC-SR04 5V + DHT22 + door magnetic contact Smoke, temperature, humidity and...

... Sensors: - MH-Z19 co2 sensor - SHT-31 temperature and humidity sensor - Display SSD1306 128x64 TODOs: - improve Wemos D1 fit (required glue now) - improve MicroUSB connector hole - think about influence of Wemos heating on measured temperature

Replaced the power jack opening with an mirco usb one.

Customized version of https://www.thingiverse.com/thing:1776349 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1776349

Customized version of https://www.thingiverse.com/thing:1768820 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1768820

Modified version of Rickvillela's sleek design, which works flawlessly. UPDATE: May 18, 2018 Added STL file with a hole for the DHT22 Shield Sensor. ...Also added an edited box for a 5mm IR LED or RGB.

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

Customized version of https://www.thingiverse.com/thing:3128599 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3128599

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909

Customized version of https://www.thingiverse.com/thing:2814909 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814909