wemos d1 esp wroom 02 pinout 3d models

This is a remix of SuperCub's AirCare - Temperature and humidity with Wemos D1 Mini and DHT22 https://www.thingiverse.com/thing:4691909 Things I changed: -Made it longer since the DHT module I'm using included the board -Raised up the little nub at...

I made this remix to be used as part of my Home Assistant Glow setup.It uses a Wemos D1 Mini v2 board with soldered on headers, the “Lid” model has extra height to allow for the connectors to fit and then wires to pass through the lid.I've also added...

This build accommodates the Wemos D1 Mini Pro / Relay Shield with headers installed in the configuration shown in the images. A small hole was left to access the reset button with a paperclip. Several ventilation holes were added to the back for...

... and using it as an extended button. To assemble the housing, print both halves flat, place the Wemos inside, and then glue them together. ...I used acetone to melt the halves into a single piece, but superglue can also be used for this purpose.

To achieve this goal, I had envisioned using the following components: A NeoPixel ring with 16 LEDs to provide an eye-catching visual representation of audio levels The Wemos D1 mini as the brain behind the operation, handling all the necessary...

I always have a few Wemos D1 Mini boards around for new projects and I got sick of having them rolling around in a plastic box where I could never find them. So I modelled up a quick insert to keep them all nice and neatly organised. These fit the...

I have designed a small, handy case for the WEMOS ESP32 D1 Mini version. Board just snaps in place (start with the USB-port when inserting) You need 4 M3x6 screws to fix the lid. There are two versions of the lid: Version 1 for directly...

Files are compiled for printing a charming little enclosure for the WeMos D1 Mini development board, designed specifically for the ESP8266, along with the OLED shield. This is part of an instructional video for constructing a compact desktop display:...

A case to hold a 12 Led NeoPixel Ring (AliExpress and not the real one from adafruit) and a Wemos D1 (ESP8266). The size of the 12 Led NeoPixel Ring is inner diameter 48 mm, outer diameter 56 mm and this is larger than the official Adafruit one.

I used an ESP8266/Wemos D1 mini flashed with ESPHome and connected to my HomeAssistant. Cramming everything into the case is quite a challenge, but in the end it should fit. ...I glued it right beside my Desk so I can toggle multiple Automations in...

The lid holds the Wemos Mini D1 in a slot that leaves the pins available. ...The bottom has holes so that it can be used with an environmental sensor such as the BMP180 temperature/pressure/humidity sensor pack.<br/> There is a cut out in the bottom to...

Wemos D1 mini Work Table holder - V2.0 Print Settings Printer Brand: Anycubic Printer: Kossel Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: REGSHARE PLA SIgnal yellow Category: Gadgets

Wemos D1 mini Work Table holder - V2.0 Print Settings Printer Brand: Anycubic Printer: Kossel Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: REGSHARE PLA SIgnal yellow Category: Gadgets

When the case is closed, the pins become inaccessible from the bottom, providing protection and security for your Wemos D1 Mini board. The case also comes with mountable feet, offering a stable base for your project. You can choose to print the...

Use some pressure to sandwitch everything together. Print the Mini Breadboard upside down and you do not need any support. Optional: For a better fixation there is the tiny holder/clamp available (antenna faceup recommend - see picture) Print...

I wanted a case for my remote light switch that uses a WeMos D1 mini and button shield. So, I designed in Fusion 360 and then 3d printed it.</p> <p>The top cover and case were designed to easily snap together, so no glue is necessary.</p> <p>My...

Additionally, I relaxed the tolerance on the Wemos board while tightening the tolerance on the sensor, making corresponding changes to the lid. If you print the lid in a translucent material, you can observe the built-in LED through it. You may need...

This is the case for the WeMos D1 ESP8266 module to be used with DS1820 sensors and Tasmota firmware. The primary function is to provide a compact case for module and jack sockets. Wiring is trivial, just connect all sensors in parallel and use one...

Human: [smily77] designed one of the smallest yet most visually appealing cases for Wemos D1 mini projects featuring an oLED display. I made several enhancements to take it to the next level: * The display securely snaps into place, utilizing a...

This 3D printed case is specifically tailored to accommodate the WeMos D1 mini variant of the ESP8266 microcontroller with various temperature or similar sensors. The model is designed to meet a range of preferences and requirements. It incorporates...

this is a system for connect safetly wemos d1 mini with dupont connector, for your project. In this way electrical connection is sure! upgrade 05/feb/21 post splitted version add version for Arduino mini and arduino nano Print Settings Printer: Prusa...

This is a simple compact enclosure for the Wemos D1 Mini. ...There are 2 versions, one with a hole for external cables, and one without.</p> <p>I have also included the Fusion360 file for ease of customization.</p> <h3> Print Settings</h3>...

smily77 made one of the smallest best looking cases for Wemos D1 mini projects with an oLED. ...I made a few improvements to make it even more awesome:</p> <ul> <li>Display snaps into place (0.96" 128x64)</li> <li>Holes for a screw and cables to...

A simple DIN-rail enclosure design for the WeMOS D1 mini. It's made of two halves that are screwed together using recessed-head wood screws. There is (just) enough space to install a simple 5V power supply cannibalised from a phone charger. ...The...

This revised design is based on my previous remix of a Wemos D1 Mini + DHT22 case, adapted to accommodate a ~25.5mm square stripboard or protoboard. The intention was to create a simple enclosure for a two-button switch controlling my living room...

But, I found that it looks like there have been some minor revisions, or maybe just different manufactures, to the Wemos Mini D1 boards since he created his... I made the following modifications to his original design: * I've widened the groove...

This case was designed to enable the Wemos as a wireless local area network access point.

This was my first try at designing a tally light case to use with Tally Arbiter software at my church.The case was designed to use-Wemos D1 Mini - AmazonNeoPixel Stick - AdafruitMisc parts and pieces-3- 6.5mm x 2.5mm magnets2- M2 x 8mm2- M2 Nuts3-...

I have designed a small, handy case for the WEMOS ESP32 D1 Mini version. Board just snaps in place (start with the USB-port when inserting) You need 4 M3x6 screws to fix the lid. There are two versions of the lid: Version 1 for directly soldering...

It is responsible for: * Attaching a 12VDC (~1A) power supply * converting the 12V to 5V for the Wemos power supply * mounting the Wemos Lolin D1 mini v4.0 * attaching multiple DS18B20 based temperature sensors * enabling/disabling up to 4 12V fans...