weirdest shapes 3d models

It can shape your arch efficiently after regularly use. Professional ballet instep shaper, mainly focuses on toes and legs and feet instep nest pressure, push and pull in the instep to feel the stretch function of feet muscles and ligaments. The...

So the measuring cup has a unique, conic shape. Also I was very keen on trying transparent material, so I really had a lot of fun with this project and extended my knowledge and experience with 3D printing quite a lot.This design is not for the faint...

(may require calibration depending on your face shape) Instances and ID Masks of materials are configured, so you can easily control a lot of material parameters. Fully compatibility with Epic Skeleton - including solved Mannequin problems, such as...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: wall_thickness = .8 height = 15 mirror = Yes shape =...

Cam mechanisms are usually used to convert rotary motion into linear motion, but can be used for the inverse purpose just as well.Required3D Printer - accommodating a build size of at least 210x80mmFilament: no specific requirements I used mainly...

10/12/2021 update:Added a mount for an accelerometer for input shaping.Updated the Y tensioner to a new, better version with less backlash which now requires an M4 bolt >34mm long. The original bolt from the old tensioner can be...

There are a few fun-looking garlic-shaped garlic containers available to 3D print that I looked at and was inspired by, but none of them were quite to my standards, which were: 1) quick print time, 2) well ventilated, and 3) big enough to hold...

Make the necessary adjustments, if this is not the case.Push the speed controller knob on its shaft (decide yourself what the off position should be)Put the wedge shaped case against the inner disc and check that the small bevel gear is aligned with...

16x 2020 V-slot inside hidden brackets 4 door hinges, same with the original ones (example: https://www.aliexpress.com/item/1005004911939089.html?spm=a2g0o.order_list.order_list_main.17.5f291802Ve5yfE) Generic corner bracket for the magnetic doors 2...

It had been quickly molded into shape after the bombing of Nagasaki, to be used in another attack on Japan, then reallocated when it turned out not to be needed for the war effort. At that time, Slotin was perhaps the world's foremost expert on...

| | marklin-front-hull.stl | Front and top arrow-shaped hull, integrating nacelle pylons, and forward deflector. | | marklin-rear-hull.stl | Rear hull including impulse unit. ...

Made this one for the wife sewing room from some color changing filament. Print instructionsgenerated by PrusaSlicer 2.1.1+ on 2020-01-07 at 12:29:45 UTC avoid_crossing_perimeters = 0 bed_custom_model = bed_custom_texture = bed_shape =...

The screw has an anti-rotation device so that it cannot be loosened by movement.        On the dolly is an adjustment scale that indicates the radius that the dolly will travel.The arrows have different shapes...

To fix this, I cut the shape of the rotation lock collar into the bottom of the assembly so that it slides all the way down and friction fits over the whole collar. This was much more stable and allowed the motor to turn smoothly. I'd like to...

I’ve also a couple of ports (antenna and micro USB) that I also wanted to exclude the fuzzy effect from around.Since PrusaSlicer allows for any shape of modifier to be used, in CAD I selected the area I wanted to be fuzzy and extruded them two...

It is designed to slot into and extend a neighboring shelf, so if you want you can even use this with the normal single/double shelf to make a funky shape, or you can add it on to the light to give it more of a functional use. The trestle is...

Remove the carbon filters.** They are cube shaped, so the best method was just using the pliers from the bottom cavity (and an Allen key pushing down from the build area) to rip off small chunks before it was small enough to shimmy out of the hole...

They need to print twice.May scale up 2x the nose clamp at Z if it couldn't hold the shape well.Facepiece 0.5mm thickness. It must be Z0.2 initial layer and Z0.1 layer height, total 4 layers.</p><p>Disc must be Z0.2 initial layer and Z0.1 layer...

No more need to print all variants of stair and riser tile combinations to get the stair shape and height just needed 6. Support "dynamic floors": make it possible to combine 1x1 floor pieces to build a mosaic or a patterned floor 7. Mix riser...

tweezers) directly at the Printer I designed drawers for mounting it under the base plate: https://www.prusaprinters.org/prints/120721-honeycomb-utility-drawer - I use 3 of them.For ptfe tube management I use...

The same design could be used for another type of water stopcock with a similar shape. For greater ease of use, it has been added the possibility of incorporating two slits to facilitate grip or to be used with a single finger. Print...

Flamethrower Tank model for 3D printing is shaped according to the tank with the same name that appears in the widely known and played 40k war video game. The tank is included in the Imperial armed forces, although only in the second-line...

Español: El objetivo de este vaso es permitir a las personas que tienen limitada la extensión de cuello beber realizando una extensión de cuello menor a la habitual. Este vaso en su parte externa tiene el aspecto de cualquier vaso, pero sin embargo...

The Base consists of a raised grid that complements the shape of each stackable unit, making a perfect interlocking system to hold your parts securely in place.&nbsp;Each square in the grid corresponds to a square on the base of each Stackable...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...

In addition, the shape ensures a perfect fit between the plates. The motor supports designed for a 4-hole M3 mounting with a 25mm diameter can be used as feet or 7.5mm square aluminum tubes can be inserted. Mounting the camera on a rostrum...

Identify the point where this line intersects with the vertical center line.Make another reference line 4.13cm up from the bottom of the box.Make a vertical reference line 0.7cm from the right side of the constraint box (the line should be between...

The vertical version needs lots of supports and has a + shape at the top which is removed after printing. I found that the vertical version runs more true as there is very little warping.</p> <p><strong>You can also find some experimental parts...

Creating the CAD for a basic trefoil knot and printing the result turned out to be easier than I expected, but developing the idea further into a large, hollow, segmented shape with matching base took a lot more experimentation.AssemblyThis build...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes shape =...