weird rolling shapes 3d models

I tried to replicate all the hole shapes to the best of my ability.UPDATE 11-13-2014I'm nearly finished with my orb! I added pictures of the (near) final paint job.UPDATE 11-02-2014I have my rims and my orbs glued together, Bondo-ed, primed with...

Since the shape of the contact is important I've included a jig for bending it. It walks pretty well with no tendacy to fall over. The arms are driven by the pins in the legs so they swing while its walking. I've seen that in a couple of Robothuts...

Once the raceway is filled with BB's, remove one or two BB's and then install the small wedge shaped piece into the bearing fill hole, the side with two faces should face out. I used a dab of hot glue to hold this piece in. 8. Repeat steps 3-7 for...

Cut the square out with a utility knife or other sharp implement Take a center-punch, or screwdriver if you don't have one, put it through the hole and touching the middle of the bottom card stock and laminate layer of the enclosure lid. HAMMER FIST...

Im gonna make a separate, smaller, desk-fixed module for landing gear, flaps, spoilers and so on.* The gear design on [this(not mine) throttle panel](https://www.thingiverse.com/thing:4445717) I found a while ago is a very clean and clever one, but...

That's why objects with ice composition can be rounded at smaller size, like Mimas; or bigger objects like Ganymede can be extremely rounded, because when a moon or an asteroid melts (usually in its early history) it turns into a rounded shape, and a...

Due to it just being a extruded shape, you can stop the print prematurely and the result will still work alright, though it may slide along the pins. There's also an svg for the profile used included, if you wanted to adjust this for a different...

Mine didn't break yet, but it's probably a good idea to add something that would hold it in place betterThe shape of the holesSince i don't have a 3d scanner, i was only able to model the holes approximately. The headphones do fit and charge, but...

Marlin-RC firmware also included in downloads (Marlin-RC.zip) If anyone plans to build something like this, I recommend using a 12mm heat-bed plate (rather than 6mm) as the aluminum plate deforms up to 5mm when heated to 90 deg C, I am using 9 x 9...

Bend the clip after 2-3 mm in the other direction (90°) to create a Z-shape. Now, wind the paper clip around the rod. The windings should be tight but not too tight to work properly. You can wrap some painters tape (or else) around the rod one or...

Integrated shaping process, round edge does not hurt the hand. Well made thick band clamps and angled fork tips to prevent band friction, will not damage bandsets. use din m3 screw to fix make easy to hold and shoot High-quality solid 3d model ...

Their shape is iconic and instantly recognizable.&nbsp;What is a bobby pin? </strong>For the bald and otherwise uninformed: bobby pins are a widely used hair accessory. They are not just a decoration - they also have a purpose - which is to hold hair...

- Design a slot on nozzle, so that different outlet sizes and or shapes can be easily designed and printed later. - I designed a spanner extension so that you can tighten the impeller into place without having to use the original tool spanner at an...

There are 3 rows of small triangular shaped ribs where the ratchet teeth are that need to be cleaned out with a knife. The teeth should be open and continuous across the width of the spindle. There are a couple of other ribs that need to be cleaned...

... around the posts. Insert the mirror tower and adjust as needed. Use scissors to cut the sun shield into the desired shape. ...For best results, cut straight lines between adjacent washers leaving some space around the outside edge of the washers.

4 - The neck to head connection is not as convenient as I would have liked due to the shape of the parts. I glued all the head parts together and glued all the rest of the parts together. Once the glue on both sections were fully set, I then...

Coorbital with Telesto and Calypso&nbsp;Orbital period: 1.888 d.&nbsp;Composition: Icy body.&nbsp;Density: 0.984 g/cm3.&nbsp;Dimensions: 1076.8 km × 1057.4 km × 1052.6 km.&nbsp;Model scale: 1:4x106 (10cm) 1:1x107 (10cm) 1:2x107...

Instructions For each support place: - make with the grinder an about 5.2mm wide slot, about 2.5-3mm deep, to the socket wrench - insert fully the socket wrench from below - insert spring and bottom cover - insert the M3x10mm screws, tapping the...

Dove tail variant has a top cap that is secured using dove tail shape while the other is just a square hole. Pillar cap is also used as pillar base for both variant of the pillar. Lift base will slide nicely into through the pillar and it is...

... what I used. Maybe. How I Designed This AutoCAD All I really did was use some calipers to get the major dimensions acquired (width, length, hole distance, hole diameter) and the overall shape was eye-balled to match the style of the original gear.

Incidentally, the value 2.5 is used in some famous superelliptic artwork, such as the big fountain at Sergels Torg in Stockholm, and also the superellipse-shaped tables by Bruno Mathsson and Piet Heins. Updates 2020-09-04 Added an experimental...

They were square in both shape and appearance, resembling many other designs I'd seen. To create a unique look, I aimed to design a case reminiscent of the classic wind-up Smiths clock that my Dad had when I was a child. Even though I designed a...

There is a J-shape built into the holes in the mouth of the lure that the 90-degree piece should "catch" in if you get it right, that will keep it from slipping out when you're reeling in. You'll want to make sure there's enough straight wire coming...

That is why the form was inspired by a mine, taking aspects of its shape and its action when exploding to bring this gadget to life. We are very happy with the result and we hope that you enjoy this gadget designed by curious Guatemalans, for...

Y Necklace - Stylish Y-shaped necklace that suits any fashion sense. Pearl Necklace - Classic pearl necklace fit for royalty. Casual Necklace - Simple yet elegant necklace designs perfect for everyday wear. #BANGLES AND BRACELETS Bracelets -...

http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror = Yes height = 15 wall_thickness = 1.6 shape =...

The shape, the size and the magnetic strength of the pet magnet affect tactile and acoustic feedback.DISC MAGNET: a 6mm x 3mm N35 neodymium disc magnet. Most disc magnets found online actually measure 6mm x 2.67mm - these are usable too. Many disc...

The EPDM pieces compensate for differences in phone shapes, providing a custom fit. The two jaws clamp onto the edges of the phone like a vise. The EPDM pieces help hold the phone in place due to their typical rubber adhesion and conform to the...

I've included a (very) basic circuit diagram in the pics that should help you wire it up properly I've also changed the shape of the battery holder, and reinforced the tabs that connect with the Xbox controller. things now connect with M3 bolts and...

In order to prevent dust and dirt particles as much as possible from coming into the slider channels of the S22 Pro the aim is to close off the beginning and the end of the sliders from particles, however you also don't want to introduce friction and...