weighted companion cube 3d models

https://www.thingiverse.com/thing:3999541List of features and improvements:2 V solid wheelson top to better distribute the weight*Eccentric nut on bottom wheel, allowing fine adjustmentsBLTouch is mounted behind the hot end, this way it remains...

Many attachments to come.. photos are showing the base and 1 motor cover, added:photos with both covers and motor wiring with XT30 connectors for easy electronics swap, nothing smart, just hot melt glue holding the connectors in one of the 10mm...

This asymmetrical pose features the shoulders turned in the opposite direction to the hips and one leg slightly forward, with the weight of the body on the other leg. Unraveling the mystery of the creator's identity The debate surrounding the...

This is so the pivot screws doesn't have to hold the weight of the light (which is 1.4kg with a 5Ah battery). Since the stand is quick release, there has to be an external cable that connects the battery to the light. I recommend you get a short...

The voids in the bases can be filled with lead to weight your chess set, or with rare earth to make your chess set magnetic. If you are going to stain, paint, and/or varnish your chess pieces, leaving the support material in the voids allows you to...

A much lighter weight, more efficient, and quieter fan duct for the Creality CR-10. It is designed to fit the stock Mk8 style red heatsink hot end. It works with the stock cooling fan. It keeps air flow from blowing on the heater block or going...

The this series is designed to provide a low profile, light weight, high performance light bar that can be mounted where other lights will not fit. These units can operate in temperatures of -40° Celsius to 80° Celsius, are waterproof to 1 meter and...

Fill it will water till you have exactly 1.96 pounds of total weight for all elements.Close the bottle with the cap, and tie the string firmly to the neck leaving a loop so you can loosly introduce the arrow in the loop.Put the bottle piece aside for...

Lay the shell flat and apply weight to fully seat. Same process for the barbed tabs. Tidy up the square edges and remove any surface bumps. Line up the tab with the trough. Make sure the barb is on the outside face. Be careful the upper edge is...

The objective I set on Tiki3 mount system are ease of print, compact, light-weight and efficient. -Looking at the side profile of the dragon or V6 hotend, the window needed to push air through is around 25mmx25mm = 625mm sq. For a 4010 the fan...

The other end is similar, but I glued a length of PETG filament instead of wire to keep weight down. Sensor: The sensor is made from the hall effect sensor from the 5V fan. This had 4 pins with two as outputs, and two for power. A 3 pin Hall...

Lengthening of Y axis, shortening of X axis to reduce weight of moving components. Reduction of extrusion usage, increase of structural use of enclosure. Usage of full sized delrin wheels on Z axis. Bed base to act as enclosure floor. Use of precut...

I have added this improvement since normally the friction would wear out the row where the switch slides and more often used tabs could just slide down under their own weight. ...I have been using those tabs for more than half a year and they still work...

I was hoping to keep this as child-safe as possible by avoiding glue altogether.Update: After extensive field testing (thank you Harper, Cora, and Brenna) I discovered that when a child puts their weight on the car this puts stress perfectly in line...

The idea came to my mind quite often but the challenge was always weight vs. size as I didn't want to ruin the speed of the Predator by making it too heavy and there isn't much space to work with... But evolution was in my favour this time! Now,...

In my case I didn't need to weight the nose but your mileage may vary there. Do a swing test for stability to be sure. Here is the (fuzzy) video of my launch... https://www.youtube.com/watch?v=6Rw_B7iuyM8 Onboard video from another launch (ignore...

I recommend using Polymaker LW-PLA (pre-foamed so it prints like regular PLA) to save some weight, but this should fly with regular PLA.As you're building, consider your paint scheme. For the example photo in this thing I assembled the tank and the...

The this series is designed to provide a low profile, light weight, high performance light bar that can be mounted where other lights will not fit. These units can operate in temperatures of -40° Celsius to 80° Celsius, are waterproof to 1 meter and...

see the filament guide at https://www.thingiverse.com/thing:6416246)I added a silica gel cannister to each box to complete the finished product – Amazon Wisesorb 40 gram.The rear spool is lowered by 2mm from the front spool to allow more room at the...

At the moment i have no holes (!) added for mounting anything, but i will provide the fusion-files to edit that for your own plugs and switches i think that even with fan and plug/switch added it wont be heavy enough to not slide on the table, so i...

Print as many as you want to make your pot as tall as you like, but be warned - I do not know how much soil can be added before this pot can't handle the weight. I've included 2 options - with strawberry holes and air pruning holes, with strawberry...

(extra screw holes are available if you plan to stack more than 2 rows of drawers or contents of heavier than normal weight.)• Prep the drawer case for installation:• Install GEN2-QL (QuickLock Mechanisms) into the drawer case. These will allow you...

once u have the chain u will need to "Post Process it" 3 close both chains (small and big) in circle 4 and start move each chain and rotate in way that all parts will rotate and scrub each other 5 this way after 10 minutes(maybe more) it will become...

The fan housing may start to sag toward the bed over time due to the weight of the fan bending the legs. Using zip ties to hold up the top of the mount against the carriage ties will prevent this. c. I printed this using PETG, as I was...

The current one is only 2mm wide in the back to keep the weight down. the problem is that it is just too fragile. The tail tends to break off. So stand by. The V2 Fuse has a slightly larger nose cavity and is 3mm thick in the back. If my test...

I wanted this one to be functional as an actual rock crawler so I put most of the weight up front and down low for steep climbs. I designed it to work with an Axial AX10 Wraith or SCX10 style transmission with an extended output shaft I had laying...

It would have to attach at the sides, because the lid detent is not reliably strong enough (depending on material, resolution, individual printer qualities) to hold the weight of the welder and battery. From sad experience, the MOSFETs need...

The this series is designed to provide a low profile, light weight, high performance light bar that can be mounted where other lights will not fit. These units can operate in temperatures of -40° Celsius to 80° Celsius, are waterproof to 1 meter and...

However, increasing the infill % (which will increase the weight of the box) and decreasing the layer hight (which will give better accuracy to the moving parts) may improve the automation. To avoid jams of cigarettes (over 10 cigarettes) during use,...

I don't think that the weight and scale of the model with the skinny Hawk wings work out very well. And to keep it to scale, the tail end is just too small to be strong enough for a crash/landing. My first attempt resulted in the tail breaking...