webcam side mount 3d models

As my webcam has no option of changing focus, I had to design a long webcam mount to alleviate this. This is the product, bolted in front of the mainboard metal casing with the same screws. Hover, whis can be mounted on any end of the base 4040...

The Microsoft Webcam mounting is different so instead of having 2 bolts down the center of the 2 piece mount clamping block, I made a mount clamping block that has a bolt on either side. I also spruced up the Arm's design a bit and carried over that...

Additional adapter for Logitech C270 Webcam Mount for the original holder. ...System works also great with PitStop Extruder</p>

A mounting adapter for the Bewinner USB Webcam (https://www.amazon.de/gp/product/B07N392J1S/) for the QIDI X-Maker.

Remix of Logitech C270 Ender 3 v2 X axis mount by Dragaa May 08, 2021 to fit an Anykuu Webcam.

Made to mount the new Opal Tadpole ‘laptop only’ webcam to a regular desktop monitor. ... Nothing fancy, but it works!

Monitor mount for webcam light Print whit no support. 0.2 Layer Height 20% Infill Share a picture! ...Thank you!

I couldn't fine a good mount for my webcam to use with octoprint, so I made my own.

... with a tripod mount adapter here) and the Microphone cap work great. I've only tested the "Side" version, but I've also included an elongated version so you can keep the "headphone" jack on the microphone uncovered by moving the camera mount.

Just a wall holder for webcam. ...I've yoused it with MS Lifecam HD 300 but i think it'll be good for any other webcam with monitor mount.

Remixed to fit this Wansview webcam I bought during the Covid webcam shortage.  Cable management based on a different remix that I couldn't find when I needed to print a replacement. ... Uses original mounting hardware.

Designed a simple webcam mount for my cheap, brandless Aliexpress webcam. Based on the design of a C920 webcam mount. I liked the simple design, that could use the built-in arm and could easily be removed in case the top table should need to be taken...

Other generic mounts tend not to work as the bezels are quite thin.I've left the fit slightly loose front to back and I've stuck a piece of foam tape (3m double sided, but left the film on one side) on the piece that sits against the front of the...

http://www.thingiverse.com/thing:2325641 is the blueprint I used for my Logitech Webcam.\r\nAt my workplace, we have a Microsoft Webcam attached to a Taz, so I'm creating a version 2 design.\r\n\r\nThe Microsoft Webcam mounting system differs from...

... Post. ... A simple Webcam mount for my Prusa i3 MK3s and the Webcam Logitech C525. You need to disassemble the webcam housing, but that is not too difficult and saves a lot of space. If you want you can glue back in the "Light guiding thing". ...

This webcam mount is a straightforward yet efficient solution for attaching clip-on webcams. It seamlessly integrates onto the inbus bolts of the Z-axis and positions the camera directly in front of the hotend with ease. ...I originally created this...

Remix of the Webcam Mounting Bracket for Ender 3 v2 to be fixed on top corner of a Lack enclosureI use it with a Logitech C920 WebCam but it will fit any WebCam with a standard ¼" screw

This mount is designed specifically for attaching a Logitech QuickCam Orbit AF pan/tilt webcam to a TurtleBot. ...If you're looking for a reliable way to integrate your webcam with this cutting-edge robot, look no further than our store at...

... mount for Creality CR-10s Pro. ... Includes a couple of different mounting options. Hardware used: 1x M4x16 screw + 1x M4 nut + 2x M4 washers (attach mount to printer) 1x M6x35 screw (connect arm to mount) 1x 1/4"x3/8" screw (attach webcam to arm)

Just needs a tripod screw (temporary tie-rips) for mounting the webcam to the adapter. I modded the webcam for reversing the hinge action. Just pop the rubber grommets and take out the screw and pin. ...Reverse the mount the webcam and put in the screw...

I searched for "cheap webcam" on Amazon, ordered the first result, and made an X-Axis mount for it! Snaps together, slim design, adjustable tilt, one support structure, and room for manual focus with the case on. ... * does fit if you have an x axis...

This sleek C270 webcam mount keeps your webcam neatly stowed away and concealed. The design effortlessly clicks on and off, providing seamless convenience. ...With its adaptable GoPro-style mount, you can swiftly swap the camera to other compatible...

This mount supports any webcam, such as Logitech C920, equipped with a standard 1/4" tripod mount screw. To install, affix the printed template onto the side rail using M5-10 screws and T nuts; post-install T nuts are recommended for hassle-free...

... I put some glue in it to hold the camera at the angle I wanted. I also glued Webcam Mount v1 and holder_2 together because I didn't have screws small enough for the holes. Webcam Mount v1 can be replaced with any part that fits your webcam better.

... that doesn't require any screws, perfect for my trusty Creality CR-10 printer. ...My webcam's clever design allows it to clamp onto a monitor, and I've rigged up this makeshift mount by wrapping it snugly around the 40mm rail - it works like a charm!

... Ender-3 S1. ...Simply slides on to the X gantry, no tools or disassembly required. V2 changes: added cable tie holes. Also included is a threaded knob to match any webcam with a tripod mount (1/4-20 threads). ...Print this part at .12 resolution.

... I had in a drawer to OctoPi and my Sidewinder X1. ...However the webcam didn't have any mounting points, and was only had a clamp style mount. ... This will attach to this base, https://www.thingiverse.com/thing:4037247, using an M4 bold and nut.

... printer using 40mm box section frame. ... It has been tested on the Elegoo Neptune 3 Pro and works well for small webcams with tripod mounts such as the Logitech C615 * No supports required. ... * I used a printable 1/4 screw from another design eg:

This is a Remix, but i can´t find the Original Post. A simple Webcam mount for my Prusa i3 MK3s and the Webcam Logitech C525. ...You need to disassemble the webcam housing, but that is not too difficult and saves a lot of space. If you want you can glue...

Create a universal mount for your webcam using Torsten's Webcam holder design for Ultimaker printers. The holder has a slot size of 0.25" x 1.75". Print the holder, clamp, thumbscrew, and optional beams (I used six). Fasten everything together with...