wd 40 cologne 3d models

Two easy-to-print hooks for adding an additional drive - WD Passport - to your Synology DS218 server. ...Add adhesive felt pads and everything will sit tight.

This is a wall mount for the WD My Passport External Hard drive that's 85.5mm wide based on https://www.thingiverse.com/make:1158524

To stack my WD elements harddrive i designed this simple loop. Printed with TPU with different heights. ...Every height between 1-2cm works fine.

Adapter to attach hose of Kärcher WD series to cyclone dust collector with 50mm diameter. ... - Infill: 15% - Please print with bigger side down - No support needed

Wall mount for WD My Passport external hard drive. I designed to accompany my Xbox wall mounted setup. ...Designed for use with #6 drywall screws.

Material — PETG (FDM) Finish — Standard (40% infill) Color — Red One of the ears doesnt quite latch, but the print still had a bit of debree under the ears, so I would attribute that to the printing, rather than the file, as that part was not...

Faulty handles for the Valberg 1D NF 350 A+ WD WMIC refrigerators break after a few months and are not covered under warranty, despite clearly being a manufacturing defect.

Adapter for connecting Hitachi / Hikoki C8FSHE or C8FSE miter saw to a Kärcher WD-6 P shop vac. Print with flat surface down, supports enabled. Snap it on. ...No need to glue, tape or screw!

Anti-theft protection is now available for external hard drives WD Elements WDBUZG0010BBK. ...These devices can be secured by screwing them under a desk, near a computer, or on a wall.

Remix for WD Blue 3D NAND SSD, also added grip ribbons to top cover for more friction during swapping. ... Note: Top cover should be printed 98% of original size.

A portable dock for a 2TB WD My Passport external hard drive, tailored to fit the varying thicknesses of this model. ...To function properly, this dock necessitates the attachment of Velcro both on its surface and on your laptop.

... perfectly. Added a 35 mm cone to the hose connection. And a hose connection with a 35 mm elbow. Kärcher WD pipe elbow 35 mm https://www.thingiverse.com/thing:5338242 Kärcher WD 35 mm male Adapter https://www.thingiverse.com/thing:5331726

The external hard drive is a WD Element, similar in size to the WD Passport ultra, so it should fit perfectly. My mom uses her MacBook Air on an armchair and prefers storing files on an external drive due to its limited SSD capacity. However, she...

A model of an external HDD holder made for WD Elements Portable 5TB hard disk. With openings for Sinkhead M3 screws, and cutouts for easy removal of the HDD. ...Can be easily made with 3D printing PLA filament on an FDM 3D printer.

Designed for WD MyPassport 2.5 External Harddisk, Hold up to 7x for storage OR 4x for hdd farming. ...Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Esun ABS Red Category: Computer

Adapter for the Karcher WD 3 P V 1.628-170.0 vacuum cleaner, suitable for other models. The transition from a standard 35-diameter hose to a 32-diameter hose is connected to a standard nozzle without additional alterations and loss of functionality...

Biltema's top-of-the-line wet and dry vacuum cleaner, the WD 1000/10, just got an upgrade with a beefed-up nozzle tip specifically designed for tackling tough textile messes. ...This enhanced accessory is engineered to deliver powerful suction and...

Fit for WD My Passport Ultra External Harddisk 2TB No support required Any material is suitable 60% infill recommended For the lid, check out this link: http://www.thingiverse.com/thing:2011503 Print Settings: Rafts: Not necessary Supports: None...

A model of an external HDD holder made for WD Elements Portable 5TB hard disk. With openings for Sinkhead M3 screws, and cutouts for easy removal of the HDD. ...Can be easily made with 3D printing PLA filament on an FDM 3D printer.

Holder/Tray for the Western Digital WD My Passport Go SSD&nbsp;This one is thought to be glued on other models. In my case I use it glued to the back of a LCD display support for the Raspberry Pi 400 (comming soon ! ...)</p>

I wanted to connect the sawing table to the WD 6 without much different peaces So i've changed a part found on the net. During printing i discoverd a fault in the drawing. Redesigned it and made a minimalistic version. ...Printing is going on.

A remix of "WD Easystore Drive Sled/Dock" by chicken007 for a 2.5" hdd https://www.thingiverse.com/thing:4228694 I wanted to print the dock, but wanted to use less filament, so I made it slightly smaller. ... The remix field on the upload page...

WD's 3.5" External Hard Drive Supports Offer a Versatile Solution for Desk Organization, Allowing Users to Mount Them Either Horizontally or Vertically on the Bottom of Their Workstation. Four Single Supports Can Be Used Independently or Combined...

I wanted to connect the sawing table to the WD 6 without much different peaces So i've changed a part found on the net. During printing i discoverd a fault in the drawing. Redesigned it and made a minimalistic version. ...Printing is going on.

Designed for WD MyPassport 2.5 External Harddisk, Hold up to 7x for storage OR 4x for hdd farming. ...Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 Infill: 20 Filament: Esun ABS Red Category: Computer

I created this adapter for Bosch GTS 635-216 to connect the Kärcher WD 6 P 35mm hose or any other hose with 35mm size. You can use this to reduce any Bosch C35 connector to 35mm. The adapter is printed in TPU. It has a pretty tight fit. Once it is...

The Biltema WD 1202/30 wet & dry vacuum requires a reliable 75mm hose connector to function at its best. This affordable little vacuum packs a surprising punch, given its modest price and hose diameter. However, the stock hose that comes with it is...

This item is specifically designed to fit the WD My Passport Ultra External Hard Drive, which has a capacity of 1TB. It does not include any form of support or raft, making it a versatile design that can be used with any material. The recommended...

Get your WD My Passport Ultra external drive off the desk and on the wall with this holder compatible with standard 1" grid 1/4" hole pegboards. It's a great setup! Make sure to check that you have the exact same model of My Passport drive as shown...

Clinique Happy Cologne - Full Details in Original Dimensions A 3D model of Clinique Happy Cologne is now available for immediate use. Designed with professional rendering software like Rhino, Maya, Maxwell Render, 3ds Max, and VRay, this 3D model was...