wave3 mic 3d models

Should work for older rhode videoo mics, not sure about the newer ones. ...Mine needed a bit of filing to make it fit properly, your results may vary.

A space that holds the table clamp and a stand (A mic stand in my case) to replace the worn-out old one.

A space that holds the table clamp and a stand (A mic stand in my case) to replace the worn-out old one.

I took a blank popsocket stl and combined it with a mic holder on tinkercad. ...Printed in PETG and functioning well.

During Teams and other calls, other participants would notice some echo of themselves coming in through my mic, a Monoprice 600800 large condenser mic, sitting about 2 feet in front of a speaker. To reduce any sound coming from the back of the mic,...

The existing designs I found didn't have any space between the base plate and the mic meaning it wasn't possible to tilt the mic properly. The part that goes into the mic mounting hole is sized at 15.30 mm and results in a tight fit that needs to...

I made a two part mic holder with matching loops to string the hair binders through which eliminated the need for a hose clamp and it will allow the microphone to swivel as needed. ... This one is designed for the Apogee MiC usb microphone but I will...

A custom-made, two-part mic holder with matching loops was designed to string through hair binders, eliminating the need for a hose clamp and allowing the microphone to pivot freely as needed. ... This design is tailored specifically for the Apogee MiC...

I made a two part mic holder with matching loops to string the hair binders through which eliminated the need for a hose clamp and it will allow the microphone to swivel as needed. This one is designed for the Apogee MiC usb microphone but I will add...

I made a two part mic holder with matching loops to string the hair binders through which eliminated the need for a hose clamp and it will allow the microphone to swivel as needed. This one is designed for the Apogee MiC usb microphone but I will add...

I needed a way to keep my USB mic cable organized, clipped to my cheapo mic stand. Designed with fusion360 and worked well for me. Of course, might need adjustment based on your USB cable and stand diameters. ... Suggest printing at 100% infill.

... plug for the [(tr)uSDX](https://dl2man.de/). ...The plug can be used with cheap Baofeng speaker/mics that are readily availble on ebay, aliexpress, etc. ... See [here](https://hb9hem.com/modify-baofeng-speaker-for-tr-usdx/) for more details.

... desk felt like a waste. ...I had my mic stand currently in the hole, but it still felt unorganized. This holds an Anker Premium 60W 5-Port Desktop charger. The mic hole, cable hole, and charging dimensions are all parameterized (Fusion file included).

The project requires printing mating threads and a friction fit mic clip - so managing tolerances is necessary - you need a snug fit on the mic and the threads need to turn freely without binding. There are three bolts - two lengths and one with...

(MIC Clip 3 - AC Clip + MIC Clip 3 - Mic Clip) ------------------------------------------------------------------------------------------------ For an amateur or CB radio microphone, a clip/holder can be mounted on the AC vent's lower louver. ...

This is a retention bracket designed to hold an aftermarket mic, from a kenwood dmx7704s stereo, in the factory mic location on the 2013 Subaru Impreza hatchback using the stock mounting screws. During the install process, I moved the factory mic...

Many people like my original hand mic mount, but some folks wanted something that would clamp onto a thicker surface, and I wanted to make some refinements, so here's version 2 of the clamp on hand mic holder for CB and amateur radio.I recommend...

This is a rubber (TPU) mount for lav mics.I've designed and tested this with a Rode SmartLavPlus mic but it should work with any similarly sized lav mic.Printed in TPU at 20% infillI hope you enjoy printing and using my design. ...To help me keep...

I used Lazerlord's fork part on my mic stand, and thought that a TPU (like NinjaFlex) would make a great combo of mic holder and shock mount. I have been moving from home office to work office enough that the rubber bands were getting too fiddly,...

This mic stand is specifically designed to work seamlessly with the Blue Ice Mic, offering a more tailored fit compared to the standard one that comes bundled with the microphone. As an individual who values precision and comfort, I created this...

in GAP02 version I set 0.2mm gap for the mic, but it shrank a little bit on my printer.(maybe slicing problem or just physical problem) So I drew a reversion model bigger, and the final product fit better. ... Extech 407744 94dB Sound...

Mic extension lead mount for under my desk. ...Print Settings Printer: Creality CR-10 Rafts: Doesn't Matter Supports: No Resolution: 0.2 mm Infill: 10 % How I Designed This Category: Audio

This is a guitar pic holder that will snap on a mic stand. ...There are 2 versions one for a 20 mm diameter and one for a 15 mm diameter.

A friend had the PTT button on his thales style fist mic shot out, so naturally did him a new one. Printed in ABS and stuck on with strong double sided foam tape. ...This is my first design!

The original toppled because I didn't have a mic to test it with. ...This is a more stable version, because it's nice to hear everyone without passing the talking stick.

The only mic holders for the Icom IC-2730 that I could find were for clipping onto an auto fresh air vent. ... I needed one that I could screw onto a surface.

I'm waiting on a TIE flexible mic holder that tends to break easily. Still need to print it out and see if it holds up. ...Wish me luck!

This is a simple mic holder for the Yaesu FTdx10. It's sized 1 in and 2 in, so 1 inch wide adnesive tape can be used. ... I used Scotch brand "Extreme" double-sided tape.

... Lav Mic Used: https://amzn.to/3agFKTp Programmable Keypad: https://amzn.to/2PG7w3L The keypad I bought seems to be unavailable in my area; here's a similar one: https://amzn.to/3ckmw0R I'm not sure if its dimensions match the original, though.

A buddy mentioned he often misplaces mic stand cable clips, so I came up with and 3D printed some. ...The design file is intended for a 14mm diameter microphone stand and features small hooks to secure the cables in place.