waterfall 3d models

It provides a list of the models. A typical tower includes mostly about 20-30 function calls, generating Lego block elements plus some openSCAD "hand code". If you download the full Doblo Factory code (http://edutechwiki.unige.ch/en/Doblo_factory,...

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

It is intended to be loosely attached, for quick removal during total eclipse photography, and as a result, may not remain well attached in a windy or gusty environment.Materials neededPLA or another rigid filament for the frame pieces.Flexible...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

2)The plastic for the case is about 0.5 kg (the lantern is large, it was made for a large candle) 3)2 hinges for caskets 15x21mm with self-tapping screws (included, sold on marketplaces) 4)a handle for the casket (you can print it, but I wanted...

Note: A Honeywell Type H filter is virtually the same size (though not tested with this model) and 3M offers a filter that claims to be compatible with both the Aer1 and Honeywell Type H. 36x rare-earth magnets, disk shape, 8 mm diameter, 3mm heigh...

There is also a reverse mount for the hygrometer that's for mounting it on the inside of glass (also fits stock model).The hygrometer has an extender for the button that switches between C\F. You will need the original rubber insert...

The body and base were printed on my CR-10S. Layer height: 0.12mm, Nozzle: 0.4mm, Perimeter: 0.8mm, Speed: 60mm/s, Top/bottom # layers: 6, Print time: I honestly can't remember... The head was printed on my Ender-2. Layer height: 0.12mm, Nozzle:...

This model will do the same stuttering if printed too fast even with the used a reduced segment count (50) in the cylinders. The trusty SD card worked for me with a big batch of these. The other solution was to slow the print down.Let me know in...

I have no model or figure of Buffaloman in a camo tank top. The bazooka is actually pointing backwards to simply be held resting on his shoulder. I scaled it to 40% and positioned it to be resting between two shoulder spikes with the hand grip...

Project: Playdough Tool Design Challenge Overview & Background: Through this lesson, students as young as five years old can be introduced to 3-D modeling and desktop fabrication, with an emphasis on its ability to provide solutions to everyday...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

    Here are some key words copied from one of these advertisements if you are having trouble:PRINTINGThis model is for someone who enjoys the process of printing,  It is easy to print but there are nuts to be inserted  in both the main body and the...

Helicopter Collective Controller Work in progress. 6/17/20 Added File Added collective_open v4.f3d (An assembled model of all the parts.) You can alternatively use my Russian style grip located here:...

...All "mandatory" supports are already in the model. This piece on the photos was accidentally done with 0.15mm layer height and it turned out fine, although I intended to print it with 0.08mm height. Everything from 0.1mm and below should be alright.

... for all of this - I am just starting to learn with Onshape thanks to TeachingTech's new series but Tinkercad is still a lot quicker for me with these simple shape kind of designs. I am looking forward to being able to create more detailed models :)

Print Settings: - Printer Brand: MakerBot - Printer Model: MakerBot Replicator 2X - Rafts: No - Supports: Yes Important Print Note: The key thing to keep in mind when printing these wheels is to use support material, especially for filling in the...

Print so that the models are standing upright, largest end down. <h3>Post-Printing</h3> <p>To disassemble the original turn signal, follow these steps:</p> <ul> <li>Remove the screws securing the lens and remove the lens.</li> <li>Remove the...

The models (keys and legends) are the same dimensions and should center at the exact same spot. It’s really difficult, and you will fail again and again, but the result is worth it (I think). You could also print the keys upright (with supports) and...

I made 2 cover models: one is you can do multiple color layeur prints and one if you can't. The multiple color files are noted CoverBox2_colorX and the single color STL is CoverBox1.&nbsp;</p><p>If you're using multiple color layer prints, the height...

If you want to save time while testing, you can print the included calibration test instead of the full model, but that is optional.Once the egg halves are printed, screw the threads in and out repeatedly to remove any stray particles. It may feel...

All necessary supports are pre-applied to the models (there is no need to add additional supports). The main body of the stein/mug prints with cylindrical supports, the left/right lid have perforated supports, the lid top doesn't require supports...

* Supports: Yes (if using Cura we recommend using the [Tree supports](https://support.ultimaker.com/hc/en-us/articles/360012614559-Experimental-settings) option and adding a 'Brim' to help the Tree supports adhere to your print bed) * Rafts: Doesn't...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

Here is what I came up with:&nbsp;This model consists of 3 printed parts. Then you need something with ø3 mm diameter as an axle. Anything like a wire or nail would do. Just cut it to a length of 18 mm. Fix the lever in the holder with this and make...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

For other sizes of tube or different grid arrangements, you can use the Thingiverse Customizer to remix your own version (the recommended way, so others can benefit from your work) or download the model and use the OpenSCAD Customizer (available in...

You can use a polarity detector app on your smartphone to figure out which side is North (+) and which is South (-).If you want to risk glue breaking loose and would rather not print the magnets into the piece, then you can just grab the models and...