watercooling fitting 3d models

I created this some time ago so I could store my fittings in a way that made them easy to organize and find when needed. It also prevents damage from them rattling around in bags as their surfaces are often fragile. The spacing is wide to allow you...

A range of standard watercooling fittings are available, inspired by Bitspower components. ...These include a right-angle male-female fitting, a male-to-male adapter, a short male-to-male adapter, a female-to-female adapter, a 3/8" (10mm) ID compression...

A to scale model, including seperate parts and O-Rings, of the Barrow G1/4 14mm hardline tube fitting

I've also omitted separate retention rings for the compression fittings as they're rarely necessary in the 3D models.The following are included:14mm Bitspower Enhanced Multi Link/Corsair XF Hardline Compression Fitting45° Angled Adapter90° Angled...

When utilizing Cura, it's essential to ensure that "union overlapping volume" is activated. This setting plays a crucial role in achieving optimal results. To further enhance the quality of your prints, consider printing at a layer height of 0.05mm.

The fitting end is designed to be used with Bitspower fittings for 12mm OD tubing. the intersection piece approxamates the size of a 90 degree fitting. # pieces can be connected with an M3 screw and nut. ... The purpose is to get the geometry of the...

I searched Thingiverse without success and decided to design a basic Slot Driver specifically tailored for slots found in custom water loop stop fittings.

I've struggled to produce a successful print and am wondering if it's feasible to use resin instead of FDM. My FDM printer leaks like a sieve, rendering the horizontal layer lines useless. I'm posting this in hopes that someone can troubleshoot and...

I use this to watercool my K40 laser, the piece is a pass through on a water bucket cover. This is my first Freecad project, I'm still learning. I hope the FCStd file is clean enough. ... It's compatible with flexible silicone tube ID 6mm x 8mm OD.

Barb Fitting G1/4" a 3/8" for Custom Watercooling The design was made in Fusion 360. I used PLA + and then gave it a layer of UHU Expanded Polystyrene to prevent any leakage in the piece. ... HOSE USED: - Diameter: 3/8 "(9.5mm); - Thickness (wall):...

This insert replicates the EK ABS inserts that prevent PETG tubing from buckling under load and becoming loose in watercooling fittings. PETG can warp around 50 to 60 C which watercooling temps will exceed, especially after leaving GPU. This can...

Waterblock for 50W AC LEDs. ... Needs G1/4 watercooling fittings and a 43x3.5mm O-Ring. ... OpenSCAD files will need path changes to work on your system.

Support for NF Watercooling Hotend. I can modify as needed. Support for Fan 30x30x10mm. ...Don't hesitate to ask.

Knurls not modelled.https://www.dazmode.com/store/shop/watercooling/fittings/specialized-fittings/stop-plugs/ml-stop-plug-fitting-g14-chrome/

I needed to upgrade my watercooling setup for a couple of my PCs and thought it was time to design my own reservoir. So, I came up with this first design and printed several using PETG and Filaflex for gaskets. This design is tailored for an...

... hot glue, but not sure if it's a good long term solution. Some kind of silicone might work better.</li> </ul> <h3>How I Designed This</h3> <p>OpenSCAD. Source here: https://github.com/spegelius/3DModels/tree/master/Watercooling Category: Computer

... in den Ausgleichsbehälter. Durchmesser unten 11mm Oben 50mm. Gesamthöhe 65mm Funnel for filling the cooling system for computer water cooling. The funnel fits into the expansion tank. Diameter below 11mm above 50mm. ... Total height 65mm

Knurls not modelled.https://www.dazmode.com/store/shop/watercooling/fittings/hard-tube-fittings/12mm-od-ht-fittings/hard-tube-straight-fitting-1012mm-chrome/

Knurls not modelled.https://www.dazmode.com/store/shop/watercooling/fittings/hard-tube-fittings/12mm-od-ht-fittings/hard-tube-90-degree-dual-ended-fitting-1012mm-chrome/

Knurls not modelled.https://www.dazmode.com/store/shop/watercooling/fittings/hard-tube-fittings/12mm-od-ht-fittings/hard-tube-90-degree-rotary-fitting-1012mm-chrome/

Knurls not modelled.https://www.dazmode.com/store/shop/watercooling/fittings/angled-adapters-and-flow-splitters/90-adapters/angled-90adapter-fitting-g14-chrome/

watercooling pump - base

Here's my design for a 3D-printed watercooling reservoir, and it can definitely be repurposed for other applications as well. ...The available fittings are perfectly compatible with 10mm inner diameter tubing.

Radiator for watercooling, 2x120 and 2 fans with grills.

Autant je peux faire des choses jusqu'à réussir comme pour ce watercooling autant je peux vite lâcher l'affaire quand il s'agit de chercher une info sur le net... Le fichier test sert à vérifier si vos impressions et le collage au sillicone sont...

Here is the rewritten text in American English: My watercooling pump design takes inspiration from EK's D5, and it can be used for other projects as well. The pump is built around a 30mm DC motor from an old inkjet printer. It works perfectly and...

This is the custom support designed specifically for the reservoir of your DIY watercooling setup, engineered to seamlessly integrate into the 5.25-inch bay slots found in most computer cases up front.

This designs are about my Hackintosh which I built. ...These parts are for the aquacomputer filter and the EK-XRES 140 Revo D5 PWM reservoir and pump unit for my watercooling system. ... the full project is on my page: http://s-technologies.eu

I hated the double sided Corsair watercooling mount for the pump so I designed a cleaner looking mount.This mount is designed to be a direct swap for the Corsair mount. You will need 4 3mm nuts and 4 3mm x 10mm long screws to mount to the Corsair fan...

Fitting.