water hose to air adapter 3d models

Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=123456 Instructions Using the following options: Little Tube Length: 20 inches Large Tube Pitch: 4 units Large Tube Diameter: 30 units Little Tube...

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=734623 Instructions Using the following options: Innovation Level = Optimal Tire Durability = High Grade Micro Tube Length = Maximum...

Customized version of https://www.thingiverse.com/thing:734623 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=734623

The tolerances are pretty tight (intentionally, since this is an air hose connector after all) once I get it snapped on, I pretty much have to cut it off to remove it (there are some internal latches around the top rim that "hook" around the plastic...

I use this adapter to connect a 13mm drainage hose to a 32mm PVC pipe that's part of my wash dryer machine setup. The inside diameter of the adapter tapers down from 32.5 to 31.5 mm, making it easy to slide onto the 32mm pipe and creating a snug fit...

I managed to cobble together this adapter by combining a Dyson to Dewalt tool by wibbcat and a Dyson hose to 32mm hose by BrainHunter. I essentially took the best parts from each, added a hollow tapered cylinder in between, and voila - both my old...

I was also thinking about this for quite some time, based on the nozzles/motors of airplanes or even the vacuum cleaner itself to try to see which was better, a 75mm or 150mm tube.Although it fits quite well, I recommend using a clamp and putting...

Needed to connect an 8mm hose, inner diameter, to a Gardena adapter. The 8mm hose goes directly to a small aquarium pump. Used an existing o-ring from an old Gardena adapter; otherwise get one with dimensions OD 16mm by 2.5 -3 mm. Printed with a brim...

I needed an adapter to fit my vaccuum hose to my bandsaw. ...I couldnt find a suitable adapter, so I bought an MK3S+ to print one myself.Part is designed for a 0.6mm nozzle with standard extrusion width parameters. 

I remixed this part to get a decent DN50 to hose adapter. Works pretty good. Hose I used is here:...

I created this adapter to link the dust collector port of my band saw directly to a 32mm vacuum hose: https://www.amazon.com/Universal-Vacuum-Hose-32-mm-x-15-m/dp/B003FTH56K The bandsaw (Scheppach HBS20) connector has an outer diameter of 40mm. ...See...

Why and whereforeIf you have started to use the camlock hose adapter (https://www.printables.com/model/461256-shopvac-50mm-camlock-connectors-with-magnetic-catc) by @peterh, but you still want to use your old Starmix hose-ends/nozzles like me, this...

Female to female adapter connects hoses together seamlessly. A small support ring is located at the bottom for easy removal, while a washer can be installed on both sides for added security. Printing this adapter requires no supports. ...Printer...

I built an adapter to link the dust collector port on my planer directly into this versatile vacuum hose. The specific hose used is a Universal Staubsaugerschlauch that measures 32mm in diameter by 15m in length, available on Amazon. The planer I'm...

Just a litte adapter to go from a 1.25 currugated pool hose to a 3/4-11.5 garden hose. Did this so I can use the pool pump to empty out the pool. ...Also see my 1.25 hose adapter to taper on the inlet of the pool hose.

... so it should be a good fit once you push it on.Normally the vacuum head uses a different non-segmented hose, which is a chore to switch over to for a quick job. So I simply keep using my Barracuda hose with this adapter to connect the vacuum head.

Hose adapter useful for connecting a homebrewing wort chiller to a kitchen faucet that has a Delta sprayer head. The sprayer hose has a non-standard connector. Unscrew the sprayer head and connect this adapter to the sprayer hose. Use some silicone...

This adapter will allow you to easily connect a Bosch vacuum hose to a Dewalt or Porter Cable sander that has the twist lock bag assembly for dust collection. Simply twist off the bag and twist the adapter in its place. Plug the Bosch hose in using...

With this adapter, I aim to connect a garden hose directly into the outlet of the partially disassembled valve, forcing the blockage back out. I'll need some luck on my side. ... Table I discovered the correct thread size by consulting:...

This is an adapter from standard 1 inch pipe to 38mm hose for hot tube drain. ...I have added a design without barbs as eventually I had to file them off to have a practical fit on the plastic 38mm wire.

This is an adapter from standard 1 inch pipe to 38mm hose for hot tube drain. ... I have added a design without barbs as eventually I had to file them off to have a practical fit on the plastic 38mm wire.

I modified it to fit inside a 24mm tap by removing the existing plastic lug, allowing for easy connection of a garden hose adapter. ...Your thoughts and feedback are welcome; please share any comments or suggestions directly in the post as I'm new to...

... it a new life on this project. To channel the exhaust air outside rather than just blowing it back into my hobby room, I got a flexible 125mm pvc ventilation hose from the local hardware store. ...Then I designed this model to attach it to the fan.

The 35mm vacuum hose adapter seamlessly integrates with a variety of tools, specifically those featuring standard ports designed for approximately 57mm hoses, including the widely used Makita MLT100 model.

**Adapter**: Used to connect the turbine to the carbon filter (100mm - 102mm diameter) **Connector**: Connects the turbine with Part_1. The holes provide a bypass to reduce stress on grobo's internal fans. **Bypass_v2**: Allows regulation of...

I designed an adapter that connects my Moen gooseneck faucet directly to a garden hose, allowing me to link my sink to a fish tank syphon/refill adapter. The unique custom thread on the Moen faucet required precise measurements, so I used calipers to...