was medusa real 3d models

if it will be on a table or desk Printing If you will be printing the 'rotated' version, refer to the 'Code changes' section (above) to make the necessary code change and upload it to the Arduino. You will need to print 3 parts; a front, a rear and...

###Customizable Name Heart Cookie Cutter This model was generated with my Customizable Name Heart Cookie Cutter. If you want a heart shaped cookie cutter with a different word or name, you can easily create your own model with the customizer. ...

The Structural Pieces For the structural pieces of the clock - the Motor and Gear Plate and the Clock Face Stand - I chose to print them heavier to make sure there was enough weight to counter-balance the Prusament spindle and the clock motor. I...

The latest software updates, live support, pre-release STL files, FAQs, and Hero Me orientation and assembly videos, as well as access to the private Hero Me Discord server with much much more for only $5.If you don’t find your 3D printer model...

The STL filenames have both the style (normal/thin/wide) and the inner diameter in mm in the filename.In case you need even more different sizes, please install OpenSCAD on your own computer and follow these instructions to customize your...

You can now assemble the case in the following order: 1) Insert 2x M3x20mm bolts/screws into the mounting holes of the DHT22/DHT11 PCB 2) Thread the stand-offs onto the M3x20mm bolts/screws 3) Insert the ends of the M3x20mm bolts/screws into the...

Starting from the joint, which is the most elaborate part of the system, you can see that there is an evolution in the model, but each version has some features that are worth considering to see which one suits the needs best.In addition to the...

There is an optional stand which makes holding onto the base and using the box easier (and stops it rolling away when you put it down).This was originally uploaded to MyMiniFactory in 2021, and I have now uploaded it here as well. I have 14 other...

All of the hardware is M3 of various sizes and im sorry i do not have all of the bolt lengths because there are a ton of them, the only major difference to this is the one M5 bolt and nut that attaches the screen mounting parts together.Warning: to...

Also this shape is very special because you can use two V Plate and invert one to create a sort of "wave" that visually connect two I plate that is place up and down.Double C Plate* : This isn't a stand alone plate, this mean this plate is useless on...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

And since it was easy to change the density on the model and the density in the print settings I made models and project files for each of the commonly used densities in case anyone wants one of those. These models require about 1/4 the material and...

“Flowing water wears away the stone”.I will separate each step assembly one by one for easier to work with, and the components included.If my calculation is correct that you will need to print about 50 cable chains link and chains cover.And here is...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

The printable version of the Hex body and top lids I created for this competition, using insights from the wooden version build experience. The printed Lift module was assembled with spare components I had. The back/side panel was quickly made...

This mounting solution was designed to transfer through man-ways and tank openings. The light head can be easily adjusted up or down 90 degrees and locked into position by simply loosening the two hand screws located on either side of the light head...

There is no need to yet again go looking for a new set of mounting hardware that was not likely to have been designed to work with each other in the first place. Here is a link to the latest install and review of the Hero Me Gen7 by TeachingTech! If...

For bigger assembly parts that have large adhesion area and for all parts of locks and claws that you want to come out clean use "Skirt")Skirt/Brim Minimum Length: 250 mmBrim Width: 8.0 mm       Brim Line Count: 10Brim Only on Outside: CheckMesh...

Each temperature reading was given at least 20 minutes to reach the steady-state before recording.The selected 300W PTC heater will not heat the internal temperature above 85 degrees Celsius even if the temperature is set to 90 degrees Celsius.When...

from here : https://github.com/kliment/Printrun/releases/tag/printrun-2.0.0rc8 --Check under which port the Serial device was installed (COM Port might vary) --Connect with Pronterface and the specific port with baud speed 115200. --Type M997 in the...

For me 3 dl of rice was enough, but the weight holds up to 3.9 dl.Attach the other end of the string to the reel center piece. If you are using a fishing line with the reel_center_s piece, pull it through the hole in the plate and tie a small...

I remixed to have the same character set for both ends.Magnet filament coupler for drybox von Fransiscus | PrusaPrinters: This was the starting idea for having a magnetic MMU interface on the 3D printer enclosure. It reinterprets the work of Kenneth...

Please let me also know how you rate the design.Unfortunately, the uber fidget ring was deleted due to a design claim, so its no longer available.If you like it, you can check out  the original print-in-place fidget ring:The original geared...

(NOTE that this is counterintuitive: adding spacers pushes the ring DOWN.)  For the two I've built, I was able to get near-perfect flatness with just 1-2 of the thinnest spacers.For tuning centered-ness, the default configuration (centered) is...

IMPORTANT If your setup is different than mine you have to modify parameters and values to fit your needs. Use at your own risk! Firmware was successfully compiled and tested with Arduino 1.8.5. Before compiling, be sure you have modified the file...

The Heart.svg (2d) file was simply loaded into openscad and extruded like this:ranslate([0,0,rubber_base_thickness]) linear_extrude(text_thickness) scale([s,s,1]) import("Heart.svg"); (where s is an optional scaling factor).Stamp 3 Rubber Hearts.stl:...

They also have a strange shape, because after I had printed all the parts, I found out that it was better to mirror the cable guides. But since I already had the holes in the lower plate, I had to make the guides fit the existing holes. In the end it...

You can now assemble the case in the following order: 1) Insert 2x M3x20mm bolts/screws into the mounting holes of the DHT22/DHT11 PCB2) Thread the stand-offs onto the M3x20mm bolts/screws3) Insert the ends of the M3x20mm bolts/screws into the rear...

I was able to get Cura 3.6, Cura 4.2.1, and Cura 4.4.1 working with my FlashForge Creator Pro 2016 for all single extruder prints. I haven't tried any other versions of Cura, but any versions between 3.6 and 4.4.1 will likely work as well. This thing...

However Thingiverse user Haz1 (https://www.thingiverse.com/Haz1/about) was kind enough to patiently print several iterations of the case and send me pictures to check the fit. Thank you Sebastian :-).</p> <p>Since I did not yet print this thing the...