warframe action figure 3d models

I'm totally new to github, so please bear with me as I try to figure out how it all fits together. Development on the code side will now be focused on perfecting the filtering and mapping of sensor readings from the breath, bite, and bend sensors,...

I have already constructed a tractor, a forklift, a racing car , a tipper truck, a figure, and other models which I am going to publish here. All required parts are already available here and new parts will be added as needed.</p> <p>This video shows...

+ Once the Pressure can be maintained I want to test how long it maintains pressure; a full day at operational pressure is my goal because it is to be armed at base camp and carried for as long as needed + I want to knock it around while under...

With the new Pokémon Let's Go games being announced, I figured this was the perfect opportunity. Disclaimer: The Switch logo is a trademark of Nintendo and the Poké Ball is a copyright of the Pokémon Company. I don't claim ownership over either one....

Some puzzle makers craft this puzzle out of wood, and it is said that the puzzle is so difficult that solvers sometimes resort to examining the grain of the wood to figure out how the pieces fit together. Are you up for the challenge? Classroom...

This mounts a Raspberry Pi 4 on the right side under the bed, which makes cable management a bit cleaner. Print the bottom part and one of the tops depending on whether you need a slot for the camera's ribbon cable or not. Also needed: 1x M4 T-nut...

Updated 8/22/2021 Somehow the head was uploaded incorrectly (I cannot figure out how it happenned). So, head_fixed.stl replaces head.stl Enjoy! Print Instructions: Supports: No Resolution: .2mm Infill: 10% Notes:** Refer to the notes below for...

Make sure that the function has cap ends checked off and will offset the lines leftward only.Delete the bottom cap end, and extend the offset diagonal line until it snaps onto the vertical axis of symmetry.Use mirror entities to mirror this hockey...

I came up with 1.5 after some trial and error and together with the 49 plug_OD I eneded up with a great fit) * plug_depth: 6 (The Wheels socket depth is a little over 7 mm but I figured this was good enough) * plug_hole_ID: 22.4 (A bit more than the...

I figured out how to do that without having to re-do the design from the start, and have now made that change. Specifically, where the form contacts the print bed the clearances between the rings is not 0.4mm wider, with that extra clearance tapering...

Now bearing a unique figure, Yatl has become a subject of intrigue among her fellow Turtlekin. Jadeshell ShrineThe small prayer sites known as the Jadeshell Shrines can be found deep within the Arba woods, constructed of stone and adorned with gold...

Links Firmware I'm currently using (github.com) Me trying to talk about it on YouTube B-struder arm Hardware required a few M3 DIN912 screws for the assembly a few M3 nuts and M3 nylon nuts a few M5 screws to mount stuff to the 2020 extrusions a few...

I also added the motor firewall with lock parts, and I'm still figuring out the front direction. Here's a small video on how to mount the kit: Next step is finishing the front direction and then making a list of hardware. ...

It recreates the complete Palace.1:12 scale (6 inch figures) This is Set #9a Rancor Cave Attribute which includes- The Blender file- Build instructions - With Print instruction for layer height for each part - Paint guide for all parts - Assembly...

I will update the Polarity Planning sheet when I figure out what the real blocks do for polarity.Special note on Angled SidesBecause angled sides can only attach to the Sactional in one way (with the angle towards your seat) you cannot place magnets...

The sweet spot for balance seems to be 22 BB's in the front section and 8 in the rattle section. 7-27-17 = Tested the new version this morning and it seems to swim great now with the new weight (BB) counts and placement. 11-10-20 = Uploaded Rattle...

I figured I had a problem with my end stops so I spent a day diagnosing the issue. It turned out that the issue was the spacing between the rods. The carriage moved easily in the centre of the rods as there was enough flex to allow movement but as...

If you are attempting this project you can probably figure that bit out. The upper spar mount plates are designed to bolt to the side of the existing upper gantry pieces that hold the linear bearing rod, and are secured using the existing bolts. The...

He saw Akio as a father figure, though the merchant held little care for his orphaned guard unless he successfully avoided an ambush on the road. Though a cat’s senses can’t always be sharp, and while nursing a hangover one morning, the young master...

Just load either the left or right side rim depending on where you want to attach it and that's it – no need to figure out how it should be aligned. To achieve the same view as in our demonstration pictures, we recommend adjusting your metals...

In this age of redundant disc drive bays, I figured I wasn't the only one who noticed this wasted space, so I did a quick search on Thingiverse. Sure enough, there were several different drawer units designed by others. They were all great designs,...

I got what was in the pictures, and after a day or two of finagling, I figured out how to use it properly. HOWEVER, this laser was designed really inefficiently! I didnt take pictures before the change, but it's original design is well documented...

You'll figure it out; it's not an difficult print. A note about safety: Other than designing spool holders, occasionally read a book, there is one book that is about me, you can find it here: https://www.amazon.com/dp/B079BT3RG6 Adapter Bonanza! ...If...

I figured if I ever had a print that needed that additional ~5mm of build volume, then I will deal with new lead screws then. I also already have an Ender 5 Pro with a Dual-Z XL upgrade for a whopping 500mm Z build height, (but still only a 220mm X/Y...

... But Highly Recommended --------------------------------- Now pat yourself on the back and go have a beer. Take a break and consult a therapist to figure out what was going through your head and why you got into 3D printers in the first place.

You'll not only be using your printing skills but also some single board computer skills - but don’t be intimidated - I was able to figure it out. Some of my resources: https://www.adafruit.com/ https://learn.adafruit.com/...

return np.column_stack([xs,ys]) curve_x_range = (-35.25 , 48) generate_point_n=2400 data_points_list = generate_points(*[float(c) for c in curve_x_range.split(), genenerate_point_n] plt.figure(figsize=(14.2,7)) x_coords,y_coords =...

----------------- ¹ I returned the M2 because I felt it had too many flaws to justify it's high price tag ($60 in Australia), and I figured that since I own a 3D printer, I could probably design and make my own head-strap without the flaws of the M2...

Last i tried printing 100% out of Tenacious, with the springs attached, the ski's were bowed upward, i could twist and bend the ski's in any direction easily and figured these would definitely not break, but they did! So i went down my own path...

I haven't got endstops figured out yet but I've got it working for now. Note that the LM8UU bearings are pretty much press-fit as I printed them. I used a clamp to press them into the printed parts, and I don't think they're coming out any time soon...