wanhao duplicator 4 firmware 3d models

This is a customized Wanhao Duplicator i3 Melzi to Ramps 1.4 Adapter specifically designed to fit into the case with ease, allowing you to fit in the power supply comfortably. For optimal fitting, please use all capital letters when printing this...

Blog post: https://juhannuskameli.wordpress.com/2021/10/13/marlin-firmware-for-wanhao-duplicator-4s-3d-printer/ Code can be found from github and commits are welcome: https://github.com/user176176/Marlin/tree/Wanhao_Duplicator_4S Notes: - Steps...

This is a zipped folder containing marlin firmware for a Maker Select V2, also known as Wanhao Duplicator i3, with ramps gen 1.4 board. Here is the kit I used:...

This version works with 2.1 machines that use a 4.7k thermistor resistor, so if yours uses a 10k one you need to change the thermistor table to custom made by Nitrogen777. SdCard support is turned off to make room for mesh bed leveling and other...

The setup surprisingly proved to be far more effective for me. ...The initial attempt wasn't quite compatible with my duplicator 3, so I tailored it to match perfectly.

Improvement of a cable support for the Wanhao Duplicator 4 involves adding stronger reinforcements and an extra clip to prevent other objects from supporting the cables. ...An additional reinforcement has been installed at the base as well.

The Wanhao Duplicator 4 virtual print bed model is available in Simplify3D. ...A custom bed shape can be found at this link: https://forum.simplify3d.com/viewtopic.php?p=12342#p12342.

This item keeps the door open on the Wanhao Duplicator Printer 4 (or later).\n\nInstructions are given below.\nConfiguration Details:\nThe extruder temperature is set to 230 degrees C°\nThe bed temperature is fixed at 60 °C.\nThe layer height is set...

Hello to everyone, this is a remix made from the original print FlashForge Creator to Wanhao Duplicator 4 thanks to the OpenSCAD model of the creator slightly modified to fit in the HBP and screws of the Wanhao Duplicator 4. A little adjustment must...

Upgrade your Wanhao Duplicator 4, the Chinese version of Replicator 2X, with these cooling system fans that enhance print quality. Previously, bridges and overhangs were difficult to print, but now it's easier with these fans in place. No printed...

Custom designer handles for the MakerBot logo on your Wanhao Duplicator 4S are now a reality. The material used is irrelevant, as long as it's suitable for printing. Infill density can range from 10% to meet your specific needs. With resolutions of...

So, I took the plunge and removed the right extruder from my Wanhao Duplicator, offering myself a choice: continue getting bogged down by failed prints caused by the second nozzle, or remove it and use a dummy to trigger the endstop, or think outside...

Wanhao Duplicator 4 / 4x Filament Tube Bracket\nThis bracket was created for the Wanhao Duplicator 4 / 4x from thingiverse.com. ...Its design includes simple brackets to push the filament tubes outward, making it easier to handle and preventing...

Flexible Filament Adapter for Wanhao Duplicator 4 Series Requiring users to drill a precise 2mm hole in the filament passage is a necessary step. Instructions Successfully printed on my Wanhao Duplicator 4x with a PLA setting of .20 at 210°.

The Spool Holder Addon for Wanhao Duplicator 4S printers, compatible with other machines featuring a 50mm diameter, 96mm long filament spool guide, is designed to securely hold any 50mm diameter holed spools in place. ...This prevents them from rubbing...

... adapter. ...This model shifts the placement of the Arduino stack more forward in the Wanhao i3's box to allow for the added height of a RepRap smart LCD controller (mine was too tall, colliding with the powersupply). ... Category: 3D Printer Parts

... Melzi to Ramps 1.4 board adapter. ...This model shifts the placement of the Arduino stack more forward in the Wanhao i3's box to allow for the added height of a RepRap smart LCD controller (mine was too tall, colliding with the powersupply). ...

This bracket will give you the ability to install the board (SKR V1.4 TURBO) in the DUPLICATOR D9 printer in addition the following component can be installed (BTT relay v1.2) Plus (BTT ups 24v v1.0) I am also interested in making a bracket for the...

This solution was specifically tailored for perspex-cased Wanhao Duplicator4 but could be adaptable to other similar models. Please note that some stress is applied to this support, which is why it's crucial to print it with a considerable amount of...

Decrease the size of the mounting holes of the original design to 2.5mm to be able to use M3 screwed to it without nuts. ...Also adjust the mounting holes spacing a bit to better align with my Duplicator 6.

Here is a replacement for those tiny nuts that secure the spools to the rods on the back of your Wanhao Duplicator 4. You might be pleased to know this modification will likely work with other printers too - because let's face it, those things are...

This massive nut was specifically designed for the Wanhao Replicator 4 printer but will likely function just as well on other models too. It is an improved version of Mike Linus's incredible NUT JOB project, with some additional features to ensure...

Wanhao Duplicator i3 Firmware This firmware is compatible with the original LCD and Melzi board. I had to create a custom thermistor table because the standard board uses 10k pull-up resistors instead of 4.7K, which I'm not entirely confident in. To...

Holes for magnet size 18mm x 2mm and for M3 x 16 bolt.

<p>I never use my right extruder, so to extend the life of my gantry motors, I removed it (along with the motor) and replaced the whole motor-extruder assembly with these two parts. The fan duct can be installed from the top (recycle the right...

I always make full use of both my extruders, so to extend the life of my gantry motors, I upgraded them (along with their fans) by installing these two replacement parts on each side. The fan duct can be mounted from below (utilize one spare fan's...

... with the Wanhao Duplicator 6. ... Redesigned the original spool holder to be longer, allowing for use of a wider range of spools available on the market. Print Settings: Printer: Wanhao Duplicator 6 Rafts: No Supports: Yes Resolution: 0.25 Infill: 40%

Here is the rewritten text: Connect the cable for your Wanhao Duplicator 6. ...Watch this video to learn how to do it: https://www.youtube.com/watch?v=y8ZgUxTTBWc.

These are the STL files for major enhancements to the Wanhao Duplicator i3, version 2. ... Improvement Design The improvement design was entirely performed using Blender software, specifically version 2.76.

The Wanhao Duplicator i3 Model uses an open-frame design, which allows for easy access and maintenance, making it a great choice for hobbyists and professionals alike. The printer's heated bed is also noteworthy, as it allows users to print with a...