wanhao cable holder 3d models

I needed a reliable cable holder for my Wanhao i3 heated bed because those high-amp wires are constantly being moved during printing operations. I've successfully paired it with my existing holder for the other side of the cable:...

This is a ribbon cable holder, specifically designed to prevent the cable from breaking at its lower weak point. It should also keep the cable securely connected. To achieve this, I crafted the design to be just as easy to install as the original...

Updated Version with stronger "Ears" uploadedThis is a ribbon cable holder and should prevent the cable from breaking at the lower weak spot. As well it should prevent the cable from disconnecting.I designed it so, that it is just as simple to...

Support pour cable de la tete Wanhao, sans cela il fini par se couper ( a peu pres 1200H d'impression, cable coupé) A imprimer en PETG, remplissage 50%

After using my Wanhao D9 Mark2 printer for a while i think that a weekspot is the thin cables going in too the printer head near the plug. So i made this simple holder for it. ... Enjoy...

After using my Wanhao D9 Mark 2 printer for some time, I've come to believe that a weak point is the thin cables going into the printer head near the plug. ... So, I designed and built this simple holder for it.

After years of use the original cable holder I printed broke when I removed the bed to replace the bearings. I decided to beef up the design a little while I was at it. I had to use slightly longer screws to get them to grab, 1-2mm longer should do...

When installing the zip tie to hold cable in the holder, I kept the locking end inside the holder so it won't catch on the bottom or on the top as the bed passes over. As a remix, used Tinkercad to extend the arm and add proper height block mount...

The design includes a flexible roll top for the ribbon cable to run smoothly along, preventing any potential damage caused by folding or pinching as it moves through the back of the housing. Additionally, forward support has been strengthened,...

To resolve this issue, I added a ribbon cable holder to the rear of the right Z axis carriage, where previous models attached the drag chain. This modification freed up space on the top of the crossbeam. This accessory was specifically designed for...

Check out my simple yet effective ribbon holder that elegantly guides that big, fat, ugly ribbon cable over the Z-axis assembly. Just feed the cable up through the hole and over the plank, then secure it down on the lower frame using a ziptie or...

I'm having a problem with my Wanhao D6 extruder cap, which comes with a cable and filament holder. The issue is that the flat cable keeps disconnecting. I found a helpful solution on YouTube in this video: https://www.youtube.com/watch?v=oqPBpaE56Ns....

Individuals may choose to attach the filament tube to the D6. ...Files included allow for easy snapping of the tube onto the ribbon cable, securely holding the tube in place.

Wanhao D6 / Duplicator 6 / Monoprice Ultimate Maker Ribbon Cable Holder Upgrade for BondTech Extruder - v1 v8: Enhanced Front Display and Secure Ribbon Cable Lock - v1 v10: Reinforced with Screw Holes, Minor yet Significant Upgrade - v2 Design: A...

Now, it is possible to mount the part to the motor as well (no chance for falling down anymore), there is also a new cable channel connection point. Instructions The models are not adjusted for ABS...

... holder to cut all threads through the bearing blocks. It's a good idea to do it on all threads as well, since it provides numerous opportunities. Print Settings Printer: Wanhao i3 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 24

Please note: The bed harness holder is designed specifically for my setup, taking into account wire placement and soldering points. These points act as stoppers, secured by 2 M3 bolts to clip the wire harness onto the print bed. You may need to...

On my Wanhao i3 the bed heater cable constantly got snagged on a metal tab at the base whenever the print bed moved forward and backward. A clever solution to this issue involves creating a simple plastic part that clips over the metal tab,...

This is plastic parts to protect the D6 extruder cable from fatigle

... also need to rotate the extruder stepper motor 45 degrees so the wires are facing the rear of my printer. Credit goes out to barbet for creating the Wanhao Rhino logo: http://www.thingiverse.com/thing:852569 Instructions: Print it Attach it Enjoy

I fabricated this bracket to prevent cable abrasion on the print head center screw following a series of electrical malfunctions. ...To repurpose the original hardware, I trimmed the white plastic spacer to size.

I installed a custom solution on my Wanhao Duplicator 6 Plus to efficiently handle both cables and Teflon tubes. ...The cable diameter is precisely 1 inch.

A sleek solution for taming the heatbed wires on your trusty Wanhao Duplicator i3. ...This nifty cable guide attaches neatly to the printer's rear, securing cables with a reliable zip tie for smooth and efficient prints every time.

A Complete Set of Essential Extruder and Cable Clips for the Wanhao Duplicator 6 Model. ... Printing Options: Printer Model: Duplicator 6 Features: Raft Settings: Disabled by Default Support Material: Enabled for Added Stability

A simple cable guide for the heatbed wires on a Wanhao Duplicator i3. Snaps on to the back of the printer and uses a zip tie to hold the cables down. ...Easy &amp; fast print.</p> Category: 3D Printer Accessories

This adapter solves the issue of uneven cable chain height between the printer frame and extruder, preventing easy flexing.\nI printed this in Carbonfill from Formfutura.\nThe holes are 3 mm and 2.5 mm, with threaded inserts cut into the smaller...

This adapter resolves a height mismatch issue between the printer frame and extruder, preventing smooth cable chain flexing. I printed this part in Formfutura Carbonfill material. The holes are 3 mm and 2.5 mm in size; I drilled M3 threads into the...

I took inspiration from [dumbcomputers](https://www.thingiverse.com/dumbcomputers) original design for this cable shroud, which you can find on [Thingiverse](https://www.thingiverse.com/thing:1473926). I made some significant changes to give it a...

Here are the print settings used for this project: Printer Brand: RepRap Printer Model: Wanhao Duplicator i3 Rafting: No Supports: No Resolution: 200 microns Infill Percentage: 50% Notes: This design may collide with the upper frame during tall...

This handy device serves as a sturdy anchor point to secure the cable firmly at the top of the printer head.