wand holder 3d models

The wand comes with a holder and some double-sided tape but the tape does not hold well in my shower and I don't want to use silicone or something else to affix it to the wall. This is intended to be zip-tied to the shower caddy that I have in my...

So I made a holder for the wand so it has a home. I used rafts to help keep the angle area clean and smooth when printing. But you might not need it. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/dditPYqapWn...

Holder for 2 Harry Potter wands printed on Artillery Hornet. Overall everything fits together nicely, a little sanding may be in order depending on the calibration of your printer. ... For the wings of the golden snapper, reheat slightly in post print...

I use my wand sparingly while washing the car, so I created a holder to give it a designated spot. The rafts on the design ensure that the angle area remains pristine and smooth during printing. You might not require this feature, though. ...This model...

I haven't checked yet how hot the handle of the wand gets, but if the temperature stays below 70°C (since it's printed with PETG), resting it while using should be no issue at all. To attach the holder to the wall, I used tesa powerstrips. These...

I designed a custom holder specifically for the Elder Wand, although I haven't tried this with any other wand yet. It was printed in PLA at 0.1mm resolution. To simplify the finishing and painting process, I divided the design into three separate...

Designed for Clorox Toilet bowl wand needs supports raft your choice

This is a holder for the Scotch-Brite Dish Wand, to prevent the soap from leaking and allow it to dry. Fits over the middle of a double kitchen sink up to 1.48" (sized to fit mine without wiggling too much). Best printed on its side with supports in...

This is a simple stand for 5 wands. ...Should hold most Harry Potter style wands. Print without supports, both parts A and B (x2) are in the different STL but will connect after printing. ...

This holds your magic wand where you put it. Strap can go around both legs. ... Use your imagination from there.

Pay close attention to the support materials located within the center of the circle, as the "wand" is prone to breaking easily.

This is a wall display for 3 wands. ... It was printed with multiple colors however can be done on one and painted.

The handle diameter is 1.275 inches (32.385 mm).The wand diameter is 0.506 inches (12.852 mm).I printed these parts in Prusament Galaxy Black PLA using the 0.30 mm Draft settings, and they are plenty strong enough. ...The upper clip has a strong grip on...

You're probably referring to a blind wand tensioner. ...It's a widely used device found in many homes, known for its tendency to malfunction or break over time.

... is 0.506 inches (12.852 mm). I printed these parts in Prusament Galaxy Black PLA using the 0.30 mm Draft settings, and they are plenty strong enough. The upper clip has a strong grip on the wand, but not so strong that the wand can't be removed.

Redesigned this remix to accommodate five wands, merging the hooks and board into one printed piece, which required shortening the hooks end for support minimization. Also revamped the plate with beveled sides to give it a more prominent plaque...

Able to accommodate multiple size wands via the screw on the top. Arm can be rotated 180 degrees by adjusted the nuts on either side of the hinge. Uses the screws I designed [here](https://www.thingiverse.com/thing:4931969). STLs prefixed with...

... to thread the screw tight should pull the nut into the socket. To mount the wand itself simply slide it into the larger tapered hole. Once secured with the screws the wand will not move. I found that even just a few turns are good enough. ...

Should hold most Harry Potter style wands. Print without supports, both parts A and B (x2) are in the different STL but will connect after printing. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Infill: 20 Filament:...

The small strips are just long enough to remove the holder if you want (the "pull to remove" handle sticks out on the underside).I've used the cheapest transparent PETG I could find and it printed great. Love that stuff, I've had more trouble with...

I designed this for the Trampa Wand remote control. I've added a small cut out in the back to fit a small sheet of metal, because the remote has magnetics built in and it sticks there light magic. You will need to cut some metal at 35x20 (HxW0...

It cradles a dish wand much like a razor rest cradles a blade in a shower stall. Open sides permit dirty water to flow downwards, away from the device and into the sink rather than accumulating inside. ...Variations boast holes of various diameters...

I built a wand that took two and a half days to complete, and it turned out beautifully. It was a tedious process due to the fact that I had my printing speed set extremely slow in order to prevent any lines or cracks from forming. ... 210 degrees of...

This is a holder for a Scotch-Brite Dishwand. My dishwand measures about 35mm towards the top of the shaft. I mounted it to the sink with some double sided sticky tape which I think is actually double sided Carpet tape, works really well.</p><p>I...

Atten ST-862D Hot air station wand holder for console hot swap HDMI replacement

... anybody who is Wicca, Pagan, or into witchy stuff. I designed this crystal wand holder to better display your wand while also keeping it more safe and secure! ...The base has a good weight to it so no matter what size your wand it will not tip over.

I found three different crests and wand holders on Thingiverse, cut them apart and pasted it together in Tinkercad I use 50% infill because I want good strength on the wand holder hooks, but less infill is probably just as good

Wall wand holder for the Harry Potterheads using the Deathly Hallows symbol. I created this for my daughter's HP room to hold her wands. There are three places on the "shelf" to hold wands. The holes were designed for the wands from Universal...

This is my wand holder/picture frame to display wands and photos from our trips to Universal Studios. Pretty straightforward build, just glue the goals to the base with the shorter goals in the front. I used a simple acrylic frame that I glued...

A magic wand holder for my daughter, in form of a capital W (for Weasley). To make it fit on my 3D printer, I've split it in two: this allows to print it in 2 different colors, in case. To print the hook, I strongly advise to use rafting, to...