wallplate 3d models

Customized version of https://www.thingiverse.com/thing:5519245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5519245

Customized version of https://www.thingiverse.com/thing:5519245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5519245

Customized version of https://www.thingiverse.com/thing:5519245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5519245

In trying to install my Blink Video Doorbell, I noticed that the new doorbell didn't cover up the existing hole. This left an unsightly look and I didn't want to patch the wall with concrete and paint. The 3d print that I made is meant to cover up...

My ethernet wall plugs are of the straight plug-in kind and some of them are at quite exposed locations. I wanted to prevent accidental damage with this custom protector wall plate. The socket protector wall plate is rectangular, and has a circular...

Customized version of https://www.thingiverse.com/thing:5519245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5519245

This is a basic single-gang wall plate designed specifically for the Nest Hello Doorbell.

The wall plate was modified to accommodate a Lutron Caseta wall switch, carefully avoiding damage to the heat sink tabs in the process. ...Additionally, reinforcing material was applied to the screw flange to enhance its ability to securely hold screws.

My wife has both of these buttons by her side of the bed and I thought it might be nice to make a holder for both. Note that for the Hue button I glued in a "fender washer" inside the hole so that the Hue button would magnetically stay in place. ...

I uploaded beveled and rounded versions. I recently purchased a Skybell HD doorbell, which covered a large gap in my brickwork left by my old one. Since my new doorbell is installed on the left wall, I angled the Skybell to face incoming visitors...

My wife has both of these buttons by her side of the bed and I thought it might be nice to make a holder for both. Note that for the Hue button I glued in a "fender washer" inside the hole so that the Hue button would magnetically stay in place. ...

Low Voltage Cable Pass-Through, Version 2: A Sleek and Professional Solution for Minimal Wall Intrusion. EDIT: Revised Design Implemented to Accommodate Thin Layer Requirements. ... Print Settings: Printer: DaVinci XYZ Pro Rafts: Disabled Supports:...

This is a sleek wall plate/mount specifically designed for the Raspberry Pi 4 touchscreen case. Simply screw it into place, and utilize the optional covers to conceal those unsightly screws. The Pi 4 touchscreen case will easily snap into the mount...

Just added another switch I needed, fits Lutron perfectly. ...Great design from the original uploader.

Wall plate to mount a keystone. I wanted something that allowed the cable to point down. This way I wont accidentally break a connector. fit's standard keystones, STL has support modeled in, no additional support needed. ...

Customized version of https://www.thingiverse.com/thing:5519245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5519245

Customized version of https://www.thingiverse.com/thing:5519245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5519245

Customized version of http://www.thingiverse.com/thing:47956 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=47956 Instructions Using the following options: Third Plate: None Plate Width: 2 Second Plate Bottom Hole:...

Tailored Version of WALLY Wall Plate Designed with Expertise of Customizer Pro Tool.

I'm wrapping up a project in my basement by constructing an office space. When I gave instructions to the electrician, I requested that he install outlets at 36" high and fit them into double gang boxes. I wanted the second box left open so I could...

A Modular Plate Panel Customizer with Advanced Options Created using a Robust and Powerful Interface http://www.thingiverse.com/apps/customizer/run?thing_id=47956 \nCreated on a State-of-the-Art Platform by Innovative Developers Advanced Features...

Works with L2620 type 240v plugs. ...I did not see any of these in stores near me and only available online, and I did not feel like spending $4 and waiting for delivery I am using it for my mining rig

<p>I've been working on utilizing Pico remotes to control <a href="https://community.home-assistant.io/t/lutron-caseta-pico-to-zha-toolkit-dimmer-control/457038">Zigbee lights through Home Assistant</a>, and I wanted some additional wall mounts for...

I've been working on utilizing Pico remotes to control Zigbee lights through Home Assistant, and I wanted some additional wall mounts for the extra Pico remotes that I wanted to install, so I remixed joshcarter's original wall bracket to add the...

Works with L2620 type 240v plugs. ...I did not see any of these in stores near me and only available online, and I did not feel like spending $4 and waiting for delivery I am using it for my mining rig This is a standard Size cover, and bows a...

Customized version of https://www.thingiverse.com/thing:5519245 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5519245

I've been working on utilizing Pico remotes to control Zigbee lights through Home Assistant, and I wanted some additional wall mounts for the extra Pico remotes that I wanted to install, so I remixed joshcarter's original wall bracket to add the...

Not perfect, but worked good enough so I used it. Can fit in a keystone jack for the hole, which is optional but thought it looked nice. Needs supports for the jack since it's square and needed tolerances to be right to fit it properly. ...If that...