walkman 3d model

Existing models didn't meet my needs, so I created a parametric part. The current parameters are tuned for use with an M6 thread and prior tapping. I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are...

It is possible that a future will make and upload a model of that piece. In the meantime, if anyone knows where to get suitable pads, please let me know. As I was saying, I started to hang them on the screw. Since the surface of the screw with the...

The casing has a channel modeled in the side to accommodate the ribbon cable coming out from the Raspberry Pi. 3) Insert the smaller end of the ribbon cable into the Raspberry Pi Camera Module, then place the module into the view port. The view port...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

unless you have a special edition like a Porsche, Mercedes, or older Audi, VW, or BMW model, which is what I have. For most of these special editions, the original push bar won't fit. I found a design on Thingiverse called *Klein-laui* and tested...

... (option code 772). From VIN F060888 1999 Mercedes-Benz CLK430 Base Coupe 2-Door 4.3L 4266CC V8 GAS SOHC Naturally Aspirated Included formats: *.obj, *.stl, *.3mf All dimensions are accurate. This model printed and tested successfully.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_left_port_length = 50 custom_top_port_corner_radius = 5 pattern_element_rotation = 0...

It does not matter which direction is taken.Continue running the line down and up between the pieces through different holes until it is fully connected.The line must turn a corner on the bottom piece, so ensure that it is placed completely in the...

It started with a Bachmann starter set with a steam loco and a couple of cars (Durango & Silverton in case my other models didn't give it away). This came with a bunch of EZ-track. I had full intention of expanding my layout so I bought more...

If you are looking for more, check out our premium projects: https://codeandmake.com/premium OpenSCAD Customizer Options You can customize everything from the size of your cards, to the number of decks it will hold and you can even create a...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

A lot of the model are just perimeters or solid bottom/top layers. The pass-through holes for the cables create small bridges first and they are closed first, and then the top cover is printed. ...So I made a few arrangements to allow decent printing...

--------------------------------------------------------------------------------- Print Settings: • Ensure the model is orientated as shown in the slicer image • Skirt - Yes • Skirt Line Count - 2 • Skirt Distance - 1 mm • Support - Yes • Support...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_mirror = 0 stencil_drawing =...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_top_port_corner_resolution = 8 custom_back_camera_x_position = 0...

At each joint- extend the cable to it's most strained position and then firmly secure it to the next joint in the chain with a zip tie. Example Setup:Though I tested all of my parts and you can assemble in any configuration you like, if you want...

... The bands were modeled separately so they wouldn't require supports and be stronger. I printed them on their sides and used a brim as they had less surface area. They will have to be glued. The main body and battery compartment required supports.

... fills the opening left after you remove the 12 volt adapter socket from the base. It simply slides into place. #Printing# I print rafts with most things, including these models, other than that they are quite simple and shouldn't cause any issues.

In later models, I have printed fins with holes to zip-tie to the cone. Unfortunately, it spoils the lines of the rocket, but it's a repair that can be done in the field. If the gantry is used, the bottle can be pumped to higher pressures - don't...

I could not find caps / hoders which suited my project, starting from inspiration of certain models existing in AA, I made a design under fusion 360 which corresponds in the size of integration, as well as the possibility of making spot welding. ...

Yes, there's an actual tank model underneath all the nonsense; it's just badly covered over since I built a spacefuture tank around it. I used a different source for my sponson lascannon; the sponson mount is from Seb's Sicaran proxy, so any of its...

... to be retained and passed through, if desired. Can be nice if you want to completely remove the controllers from your hands at times without needing to set them down. Happy Printing. I would love to hear in the comments if you use this model.

This first model is referred to as the MK1.An enhanced PLA is sufficient for the low temp extruder, but it will not stand up to the heat when using the high temp extruder in an enclosed chamber. For the high temp I used eSuns PA-CF.The high and low...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 0 custom_right_port_corner_radius = 0 custom_top_port_corner_resolution = 0 custom_top_port_corner_radius...

This also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...