vz 2000 3d models
8750 3d models found related to vz 2000.
thingiverse
Convert your Tamiya Mini 4WD VZ Chassis with our 3d printable parts, some screws and RC electronics to a full proportional 2WD radio controlled car. ... Check out the build guide at: https://airc-pirates.com/mini-4wd-vz-chassis/ VS Chassis parts are...
grabcad
... several plastic parts for the VZ.58, a mold set is necessary. ...All molds are created through 3D printing. For more details on this project, visit www.TRINOTA.com or explore the VZ.58 Engineer's projects at https://grabcad.com/oliver-137/projects.
thingiverse
Assembly and specs: The Mirage 2000 model requires: - 400g of PLA filament. - EDF 50mm and esc. - 2x9g servo, and extension leads. - Radio control reciever. - Velcro and styrofoam for battery. - 6mm carbon tube 1x 400mm, 1x 75mm, 2x 170mm. - 4x...
cgtrader
California's VZ model offers everything for free to users who want to mimic it. ...All you need to do is follow me, the creator of this remarkable AI technology.
sketchfab
The latest iteration of the VZ. ...58 Czech rifle has been upgraded with cutting-edge optics and a sleek, ergonomic fore-end grip, transforming it into a highly effective and modern tactical firearm.
grabcad
The gas port for VZ.58 rifle, mounts on barrel. It also holds lower handguard front hoop, gas piston and sling ring. Should be fairly accurate, the angle of the gas hole is estimated, but rest are measured with calipers. ... I draw it as a learning...
thingiverse
Small clip to replace the broken clip on a holden vy/vz calais flip lid console compartment. Cut/grind/sand away the remains of the broken clip and jb weld new 3d printed one in place. ...I had mine printed in carbon nylon so its fine and can withstand...
thingiverse
I modeled this to work with the vz-hextrudort and goliath hotend but it hopefully will work with the same extruders and hotends as the standard Vz-version however it might need a slight modification to their respective adapter plates. I've included...
grabcad
I've included the goliath fan duct which leaves room for the BL-Touch but the other Vz-Printhead fan-ducts should work with the normal bottom plate.You can find a BOM by searching for "Vz-Printhead-printed"Thanks Vez and MirageC for the Vzbot and...
grabcad
It is a front sight base for VZ.58 rifle, which mounts on the barrel and holds the sight itself plus has the bayonet lug. Measures should be accurate, since they are taken from the real thing. The depth of plunger pin hole is the only guestimate so...
thingiverse
HD12 carrige to suit vz-hextrudort and pcb klicky probe. i have a water cooled heatsink the same length as v6 and chc volcano heater block but it will be easy to make the part cooling tubes suit whichever hotend you are using. Hence why i have...
prusaprinters
I used VZbots sherpa mini mounting plate to reverse it and use it for the vz hextrudort for the mantis toolhead mgn9 adaption. It might work with the rook toolheads but I'm not sure and it has not been tested yet. Feel free to let me know if it works...
cults3d
This is and upgrade for the vz 61 scorpion to be able to use a 11.1v battery and cable management. There are 2 options to mod the scorpion to accepts 11.1v battery's : 1) moding the grip. ...(more easy)...
thingiverse
This is a 28mm model of the interwar Czech OA vz.30 armoured car, featuring a remarkable combination of rarity and widespread service. According to Wikipedia, only about 50 units were produced, yet this vehicle served in five different armies: the...
thingiverse
Since the standard vz-61 does not work with a normal lipo battery or at least not without some soldering and also has not that much room for a good lipo and mosfet, sooo I designed this pistol grip + Mosfet. This should fit all skorpion variants...
cults3d
Holden Adventra LX6 (VZ) 2005 Printable Car in separate parts
cults3d
Holden Monaro VZ CV8 Z 2005 Printable Car in separate parts