vw barndoor bus 3d models

Bracket for the front licence plate of an early baywindow bus. Sets the plate at the proper angle. Split into two parts for printing on standard desktop printers. ...Print Settings Rafts: Doesn't Matter Supports: No Infill: 10 Category: Vehicles

Installing a bracket for the front license plate of an early Bay Window bus requires precise attention to detail, particularly when setting the plate at the correct angle. ...To ensure accurate installation, split the process into two distinct steps...

This is a guide sleeve (Part Number 211-711-423) for the hand brake of a Volkswagen Bay Bus. I went with a sleeve and nut design, as this is easier to install versus fragile tangs. Also I printed this with 100% infill to make the parts stronger.

You can repair your broken sliding door lock lever on a 1970 Volkswagen bus, but the entire part must be replaced. To print it, place the square slot facing upwards. Printer Settings are necessary for the job. Here's what you need to do: Printer:...

This ladder was crafted to access my VW bay window camper's roof rack, following Westfalia's original design. The upper part hooks onto the drip rail while the lower section leans against the tire. Folding for convenient storage, it's quite ingenious...

... hatch so rear wall and hatch panels will be different for 55 to 63. Rear ceiling could also be longer on a narrow hatch bus. ...Also front kick panels are for the later round headlight buckets.Revisions:20/12/21 Added DXF files, DXF files are in mm

This is just a sliced version of the VW marker holder what is the base version of this remix. I DID NOT MODIFY THE STL FILES. Use the gcodes to print out the files, or use them to observe where I cut the body1 stl and the wheels. The wheels...

This model features a custom VW Samba T1 Transporter in 3D with a high-detailed exterior and mid-detailed interior; however, materials are not included. The model is designed using 3ds Max at real life scale (461cm x 212cm x 207cm) and consists of...

Front with VW Logo: https://www.thingiverse.com/thing:5260686 Wheelbase for rotating wheels: https://www.thingiverse.com/thing:5277715 Update 2022-06-01: Repaired missing face on the inside of the upper body (now V2). Update 2022-02-23: Added...

I designed this cupholder for a **VW T4 Transporter**, maybe it also works for other models (NOT TESTED!!!) This project was very time consuming ...for test printints and design :) (>50h). **Tips & Tricks:** - To print this cupholder: *It is...

Having seen the bus that ChaosCoreTech designed, I just had to print one for a friend. But I wanted it to be more - I wanted it to be lit up and have an interior. With this remix, you get: - The body with a hole for a 9V battery, the rest of the...

Smartphone storage instead Cassette storage for VW T3 bus

Smartphone storage for VW T3 Bus (instead of cassette storage)

A Hook for your VW bus -Bigger Diameter -Pinch Ribs -More stable

The Transmission with Electric Motor from a VW Type 2 Bus was Contributed by Another GrabCAD Member for Your Convenience

The classic 1960's VW camper/bus ready to print. ...This is the six window setup with a 313mm wheelbase and around 2-3mm wall thickness.

The classic 1960's VW camper/bus ready to print. ...This is the zero window setup with a 313mm wheelbase and around 2-3mm wall thickness.

These are some cargo floor parts for a VW bus 1955 to 67.Please comment if any errors are found or have additional information.

Gedruckt wurde auf einem Prusa MK4 mit 0.4er Düse, PETGDie Uhr besteht auf 4 Teilen. ...Gehäuse, Fuß, der “6” und dem “T” Die “6” und das “T” werden nur eingesetzt damit sie in jeder beliebigen (Wagen)Farbe gedruckt werden können. Gedruckt wurde das...

I stumbled upon a key hanger here and envisioned it transformed into a stylish wall plaque instead. ...To ensure its durability, I intentionally added rounded edges to prevent it from easily lifting off the printing platform.

Hello, I started from a file that I had made to put some appetizer cakes. I modified it into a sponge holder. To attach it, I put a double suction cup using the back form. ...It's perfect ...

Body Panel, Midsection and Tail Section Please Scale Up to 120 Percent

I was inspired by the Zombie Stomper, so I made some changes and added back the bottom part to the model. It's now designed to fit inside a cheap RC body that costs just $10.00. The file labeled "mirror blocks" is actually a template for the mirror...

<p>Printed at 125% so its around 10"(250mm)</p>

Customized version of https://www.thingiverse.com/thing:1680291 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680291

Customized version of https://www.thingiverse.com/thing:1680291 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1680291