vsr stock co2 holder 3d models

Created this adapter to stabilize my Hatchbox spools and prevent them from wobbling excessively on the stock spool holder that came with my Ender 3. Print two of these adapters, then place the first one over the stock spool holder with its flange...

Tool holder to organise stock Creality tool set, plus what I mostly use for general maintenance. I included a step file so you can customise it as you wish. For mounting the holder to a wall or panel you will need M4 hardwares: 1 x M4 button head...

This is redesigned holder for the VRGM gun stock that works with the oculus touch controllers for CV1, Rift S and Quest. Only the back of the controller grip is supported by the holder and your hand squeezes the controller together with the grip.

An updated version of the IR Z-Probe holder by pacman42, originally designed for the DC42 IR Z-Probe, has been created.\r\n\r\nThis mount supports Aus3D's IR Probe v1.4 on a stock Ender 3 fan shroud.\r\n\r\nThe mounting holes are 2.8mm in diameter...

... were causing problems. Specifically, the hotend fan had stopped blowing due to a broken cable. To resolve this issue, I created and printed a cable holder that attaches securely to the top of the hotend frame, keeping the cables neatly in place.

Couldn't get the spool holder to fit properly with the Ender 3's stock extension, so I figured someone else out there might be facing the same issue. Need two small nuts from the original mount for this solution to work. --------- Modified the...

кнопка фиксации магазина для VSR 10

I've designed a Spool Bearing attachment for the stock holder. Simply print the model in any color, using PLA, and remove the supports. *--Required Components--* 2 M3 screws/bolts. 2 Small Cable ties required. 2 x 624ZZ/625zz Bearings Print with...

I took dimensions off the stock holder and roller for the Creality spool holders. This should be backwards compatible with them. I designed it for M3 screw and wing nut as that's what I have the most hardware of. Could make an alternate for larger...

This is a simplified design of Hot_end_holder_with_connector_Insert from Proper Printings homing quick change hotend https://www.thingiverse.com/thing:3948924/files Simplified remix of the stock hot end + fan shroud, utilizing hex nuts instead of...

It makes the spool roll smoothly on the stock holder. I added some lines to make it easier to sand down to size, but fortunately, it fit my spools without any modifications - not too tight or loose. As far as I know, there are two different...

So I upgraded my own with a more efficient fan holder, which significantly cools down the cold end better and effectively allows for additional cooling fans for PLA. Here's what you'll need: * Sunhokey printer * 4mm fan * LED strip * Long cables...

I slapped this together using the stem of the stock spool arm so I could continue using my current printer configuration, and easily switch back to the stock arm for 1kg spools.  Print settings:I ran the first version off in 910 (nylon)...

I got tired of adjusting the spool holder every time I changed filament, so I made some rollers that fit over the stock bearings and fits up to a 70mm wide spool. You will need to remove one flange bearing from each of the original bearing spots and...

I wanted something that would attach to my Crosman Shoulder Stock and be easy to open and close, but not let the pellets spill.I borrowed some files from this project: (https://www.thingiverse.com/thing:3664788). It's a really rough hack, but it...

I got frustrated with constantly adjusting the spool holder whenever I switched filaments, so I designed some rollers that fit perfectly over the stock bearings and accommodate a 70mm wide spool. To install these rollers, you'll need to remove one...

All it takes are two 3mm screws to have a complete setup!

This design is compatible with both older belts supplied by Prusa and the Gates belts they started shipping later, which are superior but tend to slip in the stock Y belt holder. It works with either the standard idler or the Y belt tensioner...

Stock is clamp mount and has low profile but long w/magazine carrier. Confirmed mag brands are: Amend 2, Pmag, MFT, and usa made aluminum mags. Uses standard AR mag release hardware. ... Anyone print the arch Angel please post a make as I really want...

Saw someone had done crosshairs using the acrylic sheet as a holder but it just was to unstable to give me a dead center crosshair. so I started off using a balljoint design based on someone's work this was ok but kept moving. I then decided to...

Replace the ender stock spoolholder with this one with bearings I used 2 bearings with inner diameter of 15mm, outer diameter of 28mm and 7mm wide. Mount the spoolholder with M5 bolts. Braked version: On the Braked version I added some stick...

Fanduct v5.5 Upgrade for E3Dv6 & Stock Hotend - 30mm Fan Mount 30mm Fan Mount for Hot End Upgrade 40mm Cooling Fan for Your Model [Fan 40mm with Ball Bearings](https://tinyurl.com/y2zka7yn) [LERDGE 3D Printer BP6 Hotend Kit...

So you have two variants: * 2 long rollers + 2 holders with a blocker * 4 short rollers + 2 holders with a blocker + 2 holders without a blocker (for the center) This thing designed for Ender 3, but i think that this holder using on other Creality...

Just took Hiwyx's 80mm spool holder (that he linked in the comment) and added a 1cm guard

long cylinder head rail VSR 10 longer than origin vs.

VSR 10 tactical gun rail extra-long version

I really liked the idea of Ktronik, but I needed to have some closure, so as not to lose the bottle on the route, so I made a quick closure and after several routes (with falls included) and that it does not fall, I can say that it works well and is...

My bike fits perfectly thanks to this super tight fit.

3pcs remix