vs410 pro 3d models

... holes are designed in to be able to mount them and use the stock inner fender wells. Designed them specifically for my VS410 Pro with a Pro-line 66 C10 body, and axial back half cage. ...This should be a universal fit for many other bodies though.

This is a mounting platform for the Castle Creations Mamba X Electronic Speed Controller that allows you to mount it on the passenger side electronics tray of the Vanquish Products VS410 Pro. It also includes a platform at the front where you can...

This light bucket is specifically designed to work with any of the vanquish kit bodies. It is designed around the MyTrickRC 17mm round attack headlights. The fitment may vary as each pair of lights are not the same. ...However they should fit snug to...

These adapters ensure the Reefs 422 HD v2 servo remains elevated, preventing any collision with the front axle when fully compressed. ...Two units are required for proper installation.

The VS410 Pro JL body Mount set includes the front and rear body mounts and Rocksliders to allow you to mount the Axial Jeep JL body to the Vanquish VS410 Pro and Ultra chassis.

The VS410 Pro JL Inner Fenders are a direct fit to the Vanquish Products VS410 Pro chassis and match up to the Axial JL body.  PLEASE NOTE: You will also need the VS410 Pro JL body Mount set to complete the install (sold separately).

The VS410 Pro & Ultra Inner Fenders set are a direct fit to the Vanquish Products VS410 Pro & Ultra chassis and are designed to work with the stock body that comes with the VS410 Origin, Ultra and Pro. PLEASE NOTE: in this set there are 2 styles of...

The Vanquish Products VS410 Bronco interior set has been designed as a direct fit to the Vanquish Products VS4-10 Origin, PRO and ULTRA interior.

Center console for the vs410. ...Use E6000 to attach.

Simple 3 piece design to add some depth to the vs410 dash. The gauge pod sits over the sticker from the kit. Use E6000 to attach them. Print in the best quality possible, there are some small knobs. ...Have fun!

This is a small/basic plate to mount electronics next to the servo. ...I designed this specifically to fit the VS410 Phoenix, but it will fit other rigs as well.

vs410 receiver or whatever box that goes in the empty spot (if you're not running a servo winch). ...just a way to tidy up the electronics not waterproof but could be sealed

This is a battery tray I made for mounting shorty packs on the RH slider of my VS410 Phoenix. ...Should work for any VS410, and can be mirrored in Cura for use on the left side also.

The Vanquish Products VS410 Bronco interior set has been designed as a direct fit to the Vanquish Products VS4-10 Origin, PRO and ULTRA interior. ...  

a faux tool box cover for the rear section of the vs410 phoenix

Mounts the RC4WD Mojave Body on the Vanquish VS410 Chassis This has holes designed in to screw the body in place or try the blank version found...

This is a solid mount I designed to fit between the front shock towers on a Vanquish VS410 Pheonix. The hardbody I used (link below) fits directly on it, and I used velcro to keep it on. ... Link to the overall build -...

These are +5mm extended over my previous towers These are designed to fit the Vanquish products VS410 chassis

Fixed version with body mounting holes found here :https://cults3d.com/en/3d-model/various/mojave-body-mount-for-vanquish-vs410-chassis Use my Body mounts shock towers found...

Slightly extend version of the Vanquish VS410 shock tower without body posts. ...I used them to mount a TF2 Mojave II to Vanquish chassis.

mounts to extra servo location next too the steering servo

Print 2 of these and then use a piece of 1/2" rod to slide between them. ...Then use 2 m3 grub screws to keep the rod in place

Simple dash detail for the stock dash in the vanquish bodies. The gauge pod sits over the kit speedometer decal. Use E6000 to attach them. I print them in the best quality because there are some small knobs and details. ...It uses supports on the grab...

this is a small box that can go in the empty spot next to the steering servo. ...not waterproof but can tidy up under the body

This bolts in next to the steering servo and allows you to use a small battery (I use a 2200) in the front.

... 2200mah pack. ...You cannot use the rear mounted servo for the Dig with this tray This battery tray is included in the VS410 PHoenix servo relocation setup. ...https://cults3d.com/en/3d-model/various/vanquish-vs410-phoenix-mini-servo-mounts-relocation

Hinged body mount system to mount an RC4WD 4Runner body (possibly others) to a VS410 chassis. This will require some 3MM all-thread rod, M3 nuts, and 3x7x3mm flanged bearings. ...The bearings are kind of overkill so you could design an insert to fill in...

A scale engine bay designed for the Vanquish VS410 Phoenix. The set includes a 2JZ engine with turbo, Intercooler and related conduits, Radiator, Firewall with Brake booster and master cylinder. See pictures and youtube video. Print it, Assemble...

I've fabricated a platform to position your ESC and receiver at the front, where the servo winch typically resides. This innovative approach utilizes the standard hardware. ... The construction incorporated a concentric upper layer to achieve a sleek,...

winsdshield wiper motor cover for the vs4-10 phoenix