vs4 10 3d models

You'll need a license plate frame with lighting that fits perfectly onto your Vanquish Products VS4-10 Origin or Ultra/Pro body. Fortunately, this tool prints flat without supports needed. I highly recommend using LicenseMaker for making plates.

I had 2 fenders on my VS4-10 snap where they are bolted to the chassis with 2 bolt next to each other, near the bumpers.Maybe I screwed them in too tight, maybe it's a weak point in the design.These washers are supposed to reinforce that area.Print...

I've crafted a Roll Bar to fit the Vanquish VS4-10 Pro Half Cab Body, It is an easy installation that requires some drilling. The 2 base plates come with 2 x 2.5mm holes pre-drilled in them, These are the holes the roll bar attaches to, but first...

This is a versatile Mamba X ESC mount designed for the Vanquish VS4-10 pro, although it may also work on the original model. It can be used either with or without the aluminum top plate installed on top of the plastic slider trays. This mount fits...

If there are problems with spring collars from Vanquish Products S4-10 Phoenix, i hade to made my own ones. Since the kit is still on the way to me, I was only able to measure with GTS dampers from the TRX4, but since the spring caps from the GTR...

If there were problems with Vanquish Products S4-10 Phoenix spring collars, I had to make my own. Printed with a layer height of 0.1mm and 100% filling. ... Since the kit is still on the way to me, I was only able to measure with GTS dampers from the...

If there were problems with Vanquish Products S4-10 Phoenix spring collars, I had to make my own. Printed with a layer height of 0.1mm and 100% filling. Since the kit is still on the way to me, I was only able to measure with GTS dampers from...

storage stand for rc crawler Vanquish Product realized in 0.2 on raft without stand

This spacer allows for the installation of a cab-only style body (like the Proline Chevy K-10 depicted) on the Vanquish Products Phoenix crawler chassis while still using the attractive stock rear cage. ...The sand ladders (not included) hide the dig...

This grill has been designed as a direct fit to the Vanquish Products VS4-10 Origin, PRO and ULTRA kits. ...The Grill bolts to the body with the stock screws.

This grill has been designed as a direct fit to the Vanquish Products VS4-10 Origin, PRO and ULTRA kits. ...The Grill bolts to the body with the stock screws.

Electronics tray to be placed on the rightside skidplate of any VS4-10 platform. ...It will secure a Mamba X ESC and provide a waterresistant space to place receiver (rx), external BEC, light- or winch controller.

This grill has been designed as a direct fit to the Vanquish Products VS4-10 Origin, PRO and ULTRA kits. ...The Grill bolts to the body with the stock screws.

Basic tool to help get the shock collar threaded onto the shock bodies on the Vanquish VS4-10 Phoenix. Several people (myself included) had issues cross-threading the collars, so I knocked out this simple tool to help hold the collars straight while...

The electronics tray is designed for placement on the right-side skid plate of any VS4-10 platform. ...Securely holding a Mamba X ESC in place, it also offers a water-resistant space to accommodate a receiver (rx), external BEC, and a light- or winch...

This one-of-a-kind cap was crafted specifically for the VS4-10 Slider base, designed for use with a Proline Power Wagon body. ...Prior to installation, I had already modified the slider, which is clearly visible in the accompanying video.

update---- Front body mount has been shortened to fix cab angle. ...VS4-10 Parts for Cliffhanger Cab only Body. OD servo mount but no dig mount. ...Recomend to print in PC or ABS or Nylon SLS You will need to use M3 heat set inserts (4.6mm OD)

Made my own servo mount receiver box for my vs4-10. would call it splash proof. ...Could run a Axial/Traxxas style wire grommet in the hole in the side and seal the lid if you wanted Please forgive my shotty printed yellow PETG, would rather print in...

... cover together, you will need two 8mm M2 screws. For more information on this project, please visit my RCCrawler Build thread at http://www.rccrawler.com/forum/vanquish-products-vs4-10-origin/613485-vs-4-s-build-volt-up-gear-down.html#post5979544.

The Servo Cover is crafted specifically for the Vanquish VS4-10, paired with its VFD transmission. It securely attaches to the stock gear cover using double-sided tape, providing ample space to accommodate two servos and body posts. The design...

This piece replaces the inspection cover on the transmission with a body clip mount, making it much easier not to lose them. You will need to find the rod that runs through this piece - the smaller it is, the easier it will be to clip the body pin...

Print 2 of each part. ...The LED gets sandwiched between both peices.

Das ist ein Überrollbügel für meinen Vanquish Phönix in verschiedenen Versionen, er lässt sich in diversen Materialien drucken. ... Ich habe eine lange sowie kurze Version online gestellt, konstruiert sind noch einige andere

For those wanting to remove their Vanquish Fordyce bed sides but retain tail lights. Uses all stock hardware for the light housing and housing bracket though the screw mounting to the frame could stand to be shortened some. Don't know what I will use...

Cage arriere pour VS4 10 de Vanquish. ...se fixe sur les 4 vis qui tiennent le plateau arrière.

First thought it would be fun to just toss one of these in the back of my 1/10 Vanquish VS4-10 Fordyce. But then I thought this would look really rad as a fuel cell. ...Will update later when I finish building the rear frame structure to fit the tank.

winsdshield wiper motor cover for the vs4-10 phoenix

This creation was crafted using Tinkercad's intuitive design platform. ...You can modify it online at https://www.tinkercad.com/things/kgoo655r4Jk

To clarify, SCX10 ii transmission used in AX90046, SCX10 iii (non Base Camp), VS4-10 Pro, TRX4, TRX6 transmissions can be used without the bed raiser. Shortened, stiffened and redesigned shock towers ensure that the bed does not need to be cut to...