vr chat on oculus quest 2 3d models

Print replacement straps for your Oculus elite (with or without battery) strap. There are three versions included:One piece original size (needs bigger print bed)One piece Prusa MK3 bed size (should fit most heads but may be tight if glasses...

.2  2 layers concentric infill

Modified to allow mounting to the CAMVATE Universal C-Clamp: https://www.amazon.com/gp/product/B018RLY6B2/ Particularly useful for temporary desk mounting, such as when doing VR dev work. (Note the clamp uses 1/4"-20 screws, not metric. ... I used...

... the layard. To install the layard: first put the lanyard in the hole, then loop over the clip and secure it in the 2 little hooks on each side. See photo. That how I install it but may be you will an other way haha. ... Print it flat, it's easier

... is a Minimal Print. ...intended to save filament Designed for both Headset and Controllers Required materials: 8 screws Notes: -You will need to print of 4 of these, 2 for the headset 1 for each controller -Print on its side to ensure maximum strength

... Then loop over the clip and secure it in the 2 little hooks on each side. See photos. ...That how I install it but may be you will find an other way haha.Print it flat, it's easierPrint SettingsRafts:NoSupports: NoInfill: 100Filament: PLA Grey

It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter embossing doesn't need it. Spade - Infil to add weight, no supports Letters - Print flat, already scaled to...

It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter embossing doesn't need it. Spade - Infil to add weight, no supports Letters - Print flat, already scaled to...

Slight remix to hang both controllers with only 2 screws.

After I finished sanding and spray painting this, I connected the triggers and buttons, and used a normal printer to make a BMW logo sticker to put instead of the Oculus logo. You will also have to use a knife to widen the whole at the bottom a...

There are 2 versions of this, one with AND one without secure tabs. Designed in Fusion and printed with Windows Print 3d using ABS. The rims for both are beveled. 1. Without Tabs - Just press the O into the rim. The rim is beveled and is...

remix grip from https://www.thingiverse.com/thing:4651978 608 2RS bearing * 2 20mm magnet rubber band M3 bolt nuts

There is a recess within butt to conceal the knot. There is a hole in the butt that will fit a quick release sling swivel. Support free printable parts Print left or right handed controller clamps Print 3 clamp nuts Print one of each of the remaining...

Remixed from https://www.thingiverse.com/thing:4629958 This clips on to the loop on the back of the elastic headstrap.

This model requires a 1.5m hook-and-loop fastener. ... You should cut the hook-and-loop fastener to 5pices. 3 for the battery - mount, 2 for the mount - strap. ... The battery must be mounted upwards.

Its a remix only bc I added 2 screw holes to the headset part, other than that credit goes to the OP. Thanks Headset didnt need support but the controllers did. I used tree, everywhere. ...

Remixed from https://www.thingiverse.com/thing:4629958 This clips on to the loop on the back of the elastic headstrap. Category: Video Games

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

Headband for DAS Mod, includes a a buckle you have to glue on top so you can slide the end of your DAS nicely under it. Print with support everywhere. ... Remixed from: https://www.thingiverse.com/thing:3664951

The headset mount is a remix of a design from lensfort on Thingiverse that allows me to hang it on my pegboard: https://www.thingiverse.com/thing:4630669The controller mounts are an original design.You'll need support material to print the hooks for...

A battery holder for the EAFU Portable Charger, Compact 10000mAh as found on amazon for only $10-15 usually. Its cool to see a number percentage left on your battery. It's a little tight the first time you slide it in but it gets looser later. It...

Headband for DAS Mod, includes a a buckle you have to glue on top so you can slide the end of your DAS nicely under it. ...Print with support everywhere.</p><p>Remixed from: <a...

... clip to use with any cable up to 7mm thick. ...any cable smaller will fit but be a bit loose Printing: orientation: Make sure the print is on it's side this way it prints best and cleanest infill: best result use 100% but above 30% should work too

... For some reason Thingiverse won't let me select both as a remix. My version also added some holes in the strap for comfort and cooling. I printed this in TPU and 20% infill. you may have to adjust this depending on how soft your material is.

Printed without supports 30% infill is probably overkill printed at 100% scale it is fairly loose on the mount (cable tie added some resistance) can be used also just to add some weight to the back of the headset i wasn't sure how much space the...

Printed without supports 30% infill is probably overkill printed at 100% scale it is fairly loose on the mount (cable tie added some resistance) can be used also just to add some weight to the back of the headset i wasn't sure how much space the...

Other hardware: 9 x M4 10mm counter sunk Allen head bolts Magnets: use high strength neomydium magnets, 20mm x 2mm discs are cheap and readily available on ebay, 5 in the front controller clamp, 8 in the rear clamp and up to 3 in the body. 18mm x...

I measured the straps on my controller to ensure they could pass through (including the plastic thingy) but the fit is snug. You should pinch the strap and push it through a little, then line up the plastic clip to go into the hole. ...Then, if you pull...

Beware that I made it in Tinkercad, so it could be a little off and a-symetrical :D I used another stl on the internet for the dimensions of the arms that go around the head strap. ...I am not able to find it anymore, so can't credit the maker for that.

I was wondering if Quest 2 straps could be made compatible to the Quest 1. Indeed, it is possible. I liked the design of @sekazi (https://www.thingiverse.com/thing:4624192), but the adapter is movable, so I decided to make it 2mm longer and added a...