voyager 1 3d model

This model currently comes in 4 variations. Standard rail facing forward. Standard rail angled 5 degrees to the side off the rail. Standard rail with sidekicks facing forward. Standard rail with sidekicks angled 5 degrees to the side off the...

If you are worried about fit and don't want to waste filament, a test print that's just a few layers tall will work well.AdjustmentsThis model was designed in OnShape, which makes it easy to adjust the design; just click here to copy and modify the...

Furthermore I created the endstop mounts which are already present in the Fusion 360 model. I will try to update the pictures today or tomorrow. Now it gets exiting! Electronics are next! **Update 9** (03.07.2018): After test driving the Z-Axis I...

It can print without support, and if you have the workflow dialed in, it takes only about 30min per label from start to finish. You might get away with printing just the modell without the support stuff…. didn't try. Depending on your bridging it...

In this case, I have proven that it is valid for several models of Epson projectors, which are the ones I like the most, seriously, I hate dlp projectors. They tire my eyes a lot and all of them, to a greater or lesser extent, create a rainbow...

But the base design is a mix of: Ichibey's Sakura CoreCube Hbot modeling work Jetguy's lasercutter templates and electrical / extruder configuration DNewman's Sailfish programming for CoreXY gantries Credit should go to the above -- I'm just...

In order to make it much easier to assemble the case with the RPi4, a few changes were made:Divided the lower part in two halves for easier inserting ofRaspberry Pi;Added snap fit link between upper case and lower case;Using four M2.5x4 screws is...

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

Presupported in 32mm and 75mm scale [Medium Model Size] [Statblock included in our 5E Campaign: Divine Awakening]   The third child of Tharador, Renmaeth is the custodian of his body, the continent of Tharador. In the Age of Creation she shaped the...

1x set of speakers from MacBook Pro model number A1226, A1211 or A1260. 3W Bluetooth amplifier module TE657 This module goes by many names, so compare pictures when you're unsure.ebay.com / banggood.com / google LiPo charger module TE585 a.k.a...

My original plan was to also model a strap clip for the bottom of the mount, but I found that it was unnecessary, as the entire thing can be attached directly to the head strap and head pad with a velcro strap. I used a couple of long velcro cable...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

DO NOT LOOK AT THE SUN WITH THIS!Also have a look at my improved Dobsonian Design:https://www.printables.com/model/317112-propdob-telescope-foldable-travel-dobsonian-45-mir Hi, this is a Newtonian telescope with a 114 mm diameter mirror and...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them). Printing and InstallationAll parts can be printed...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

For that reason, the drawers shown here have been modeled by means of [OpenJSCAD](https://openjscad.xyz/dokuwiki/doku.php), which give you the possibility to adjust them just by changing a few numbers and [rerun the script in your...

Cap for benq projector lenses, designed for the mx660 model. It fits perfectly. On the outside it has the logo of benq and on the inside that of ho-kago tea time (musical group from the anime k-on). This projector did not have the cover when I took...

1x M6 square nut - model allows for 5mm thick, 10mm square 1x M6 set screw (10mm length recommended) Important: while printing you MUST put a pause at the layer just before the nut is covered up. Look for the small "box" cavity in-line with the...

Five basic shapes are available as elements:pieces with straight ends, adapters with either two plugs or two sockets, T-shapes, L-shapes cross-shapesTo make your own drawer partition, make a sketch like the image below, calculate...

A lot of the model are just perimeters or solid bottom/top layers. The pass-through holes for the cables create small bridges first and they are closed first, and then the top cover is printed. ...So I made a few arrangements to allow decent printing...

A simple to assemble version of the ER11A Z axis probe that screws onto an ER11A spindle. It has indicator LEDs and can be used to measure and compensate for a bed that isn't flat when engraving, for example a PCB or a curved surface. I use it for my...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be omitted on the inside. These connectors are specifically designed...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

Before you merge them, DUPLICATE the logo "hole" model (Ctrl D) do not use copy paste it will "shift" duplicate will keep it where it is. Now shift select the body and merge to make your hole cut. You will note you still have the duplicate hole. Now...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp How to create your clamp & accessoriesSelect the clamp size relevant to the...

Originally designed for the Ender 3-V2 model, reusing the 4011mm Original axial Fan as Nozzle cooling. The original fan is loud, you will probably wish to change it with a quieter one and higher performance 4020 axial fan! Many options are available....

As far as assembly is concerned, it's all pretty self-explanatory when you see the models, but here are a few tricks: Use as little wire as possible, but make sure you use good wire. The wires run from the grip and back, across the side of the...

Crawl-back happened to me exactly 2 times in the past year or more of using these reels, but I thought adding this might reduce that risk a bit.I added a model for a Jo-spacer that is useful for some Jobo center cores that don't have that...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   A Ranger from Nan Thalias. Ervion was sent as part of an Elven diplomat’s escort, alongside his father which was attacked by a retinue of goblins and bandits near the County...