voxelab polaris 3d models

Pinet Catch For cupboard doors I am using a Voxelab Aquila to print this. ... Using 100% infill Density Cubic Infill Patten Print Speed 50mm/s Inner Wall Speed 50mm/s Printing Temp 200c Bed Temp 60c (if you have a heated bed) Also using...

Printed with a Voxelab Aquila. 0.2 No supports needed (but recommended anyway) PLA. Simple cup holder for the Nord Active Plus baby strollers. Works like a charm. First design and first publishment. Please be gentle. Greetings from...

... out for a 25cmx25cm bed and the model includes any required supports. I have had success printing with default settings in PLA on the Voxelab Aquila. ...Any feed back or suggestions for better prints (on other printers maybe) are more than welcome.

Here Is my Version Of a 1 x Axial AND 2 x 4020 Blower Hotend Mount for MY Voxelab Aquila C2 ( E3 Clone). I Looked all over for a suitable solution that would work- Cool Well - Fit Well and not cause heat Seep. This is the end result of many prints...

His original part did not have a spot for attaching cabling as the original extruder assembly does on the Voxelab Aquila. This is for all those who want to cable manage at that point. *Edit: Added Picture of the Complete assembly installed...

... of the extruder. ...The gasket is the gasket required for upgrading the voxelab aquila-x axis guide rail, so that the trigger switch meets the sheet metal. Welcome to purchase unitak3d products. ...Please pay attention to our continuous updates······

A clip to hold the cables of the Voxelab Aquila off of the bed while its printing. Will need to print both parts. ... Will need 2 M2x12 machine screws with 2 M2 nuts and either 2 M2x8 machine screws and 2 more M2 nuts or 2 M2.5x8 machine screws.

I flipped the curve so that it lines up with the spool and extruder properly on my Voxelab Aquila X2. On the original version the loop pulled the filament towards the front of the machine, away from the extruder. ... This reverses the direction so it...

... ...Hold the ring and insert the opposite end into the drinking slot on the lid, pressing firmly to snap the plug in place.This specifically fits the Solo Traveler TLP316 model lid.Designed in Fusion 360, successfully printed in PLA on Voxelab Aquila.

... Funnel with air vent to fit 31mm opening on 5ltr jerry cans. ...Print in Vase/spiralized mode. Print Settings Printer Brand: Voxelab Printer: Aquila X2**Rafts:** No Supports: No**Resolution:** 0.2 Infill: n/a **Filament:** any PETG any Category: Tools

... is a boot for a 64 oz water bottle. ...It has cushioning from infill so it can be set down hard even if filled to the top. It is more far more protective than a normal bottle boot and it will prevent many dents. I use Voxelab Aries as my 3d printer.

... so that the square mold and the circular one are in different files, just for the people who need it. ...I have printed them in TPU on a voxelab aquila He separado los moldes y los he subido tal cual eran, los he impreso en TPU en una máquina aquila

... this model for one of my players in my D & D game. ... He wanted a Tabaxi Snow Lepard Rogue.  I printed it on my Endor 3 using Voxelab pla at 220 degrees.  Sliced it in Cura. ...My resolution was at .008 using supports and a raft and 20% infill.

I added the Ender Extender 300XL Kit to my Voxelab Aquila so I had to change the bed wire strain relief bracket. I had installed the Ultimate Bed Leveling knobs, so I also integrated that design with the bracket. ...I hope you find it useful.

Remixed for a Voxelab Aquila (Ender3) print volume. Prints in two pieces. I CA glued the two pieces together. If I had to reprint, I would scale the dispenser down a bit since it is made for extra large eggs. ... No supports required (some...

When switching to a BMG Clone extruder on my Voxelab Aquila X2, it turned out that the filament sensor did no longer fit. It needed to move over a bit and be raised, so I designed this quick support/mount for this purpose. ...

... reading a book. ...I liked the original so much I made this one for my desk at work, where if I goes missing I won't be too upset. Printed on a Voxelab 6, but there's no reason it shouldn't print in FDM The parts are separated for ease of printing.

Remix of the Satsana hot end shroud for the Voxelab Aquila. ...this shroud is made to accept a 6010 hot end fan (instead of the stock 4010) and 2 4020 part cooling blowers (instead of the stock 4010) Print it with the back on the build plate and...

... a type of block that i made in blender. ...its really fun to fidget with. im using an aquilia x2 from voxelab and it prints great. ...my printer didnt need supports, although you could size it up to be able to play with or as like dice of some sort.

It's a nipple wrench with a flat screwdriver and a bigger part to compress the black powder in the cilinder, it works on my Remington model 1858 in 44 cal, it should work also for more or less all standard cap revolvers Infill 60% Support yes Printed...

... got tired of my glue stick rolling off onto the floor or coming up missing, so I designed a "cup" to hold it to my machine. ... i mounted it using an existing screw and added a washer because the hole was slightly too big. I used a Voxelab Aquilla 2

... attaches to the bracket already on the printer. ...some spools don't have a big enough center hole to fit on your holder, this should fix that. fits onto brackets already on the printer, and works on: voxelab Aquilla, cr 10 smart, ender 3, and more.

A very simple hot-end shroud upgrade for the Voxelab Aquila. Designed to use the original mounting hardware and the stock fans. It can also accommodate a 4020 fan using the 4020 fan plate. Includes a handy hook for cable routing. I've measured...

This is a filament guide rod for Voxelab Aquila X2. It mounts directly underneath the filament run out sensor in place of the bushing that are mounted under the sensor from factory. I simply used a basic 3d printed "bearing" for the filament to...

... a replacement tray with the wing clips embedded into the tray for extra strength and ease of installation. A vertical print orientation works best. Included in the download are the Fusion 360 file, an STL, and GCODE for a Voxelab Aquila.

... 2020 extrusion to fit dual Z Stabilizers. Print Settings Printer: Voxelab Aquila Rafts: No Supports: Yes Resolution: 0.2 Infill: 20 Filament Brand: Eryone Filament Color: Purple Blue Black Filament Material: Silk PLA+ Filament Temperature: 225 C

this is my first design. ...it is used with the harbor freight 4box storage containers. and is designed to be used with #4-#6 x 7/8in yellow drywall plastic anchors. i printed on a voxelab aquila with pretty much basic pla settings.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hTvslAw5bRt This was made for a 4.3" Furrion Monitor I printed it on my Voxelab Aquila. ... Just needs a 4mm X 1" bolt and lock nut.

... part scratching cameras. ... dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Use the Voxelab Aquila standard PLA profile to print. ...

A small guiding hand for the Aquila Voxelab. Used with a dual gear extruder. I made it to be able to be slid friction fit on or bolted on to the empty screw holes. I use an aluminum dual gear extruder so i dont think it will work for the original...