voxelab polaris 3d models

I adjusted the mounting holes so that it matches up with the Aquila X2 carriage plate.

So you finally decided to replace the stock extruder with the beautifull red dual gear extruder. And you found out that the filament sensor no longer aligns with the new extruder: wrong height and not in line. This adapter tackles both problems. You...

After having a lot of problems with leveling my bed for the Ender 3 V2 because I was a noob this bed leveling test was very helpful for me. (Precise pictures will follow when I get a Camera) <font color='red'>Note: Cura 4.11 has a bug that does...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

This is to help mount a panel which should be 13" x 11" and cut at the corners so that it can fit in the recessed sides. I found OPTIX11 in. x 14 in. x .093 in. Acrylic Sheet @HomeDepot for less than $8. I have yet to design any panel adapter for...

After installing a BLTouch on my Aquila, I had a spare Z endstop. So why not repurpose it to be a filament sensor! I tried to design it as a simple replacement with stock materials. The only change needed to the Z Endstop is to bend it a bit, as...

This adapter gives you a mounting point for a 10 mm M4 pneumatic fitting and retains the stock filament sensor. ... The fitting is commonly used for dry box connections.

This mod replaces the default rotary knob with a winged one so it is possible to rotate with only one finger which is faster.Made a version with shorter wings so it hides the screen a bit less.Remix from Chrizz on Thingiverse :...

These are easier to install and work around, and works for all four feet, thanks to a few details. A tapered design makes room for the mainboard and power supply covers. Slots allow side to side positioning that helps with alignment and getting the...

Lay the plate on its side in such a way that the conical mounds that have the holes through them that mount on the back of the carriage plate is face down. ...You want your layer lines for the stepper mount to be going vertically when the part is...

i really like Satsana remix by Nazar78 but i got a CR Touch and it just didnt have the notch for it while there is other Satsana with cr none still had all the other parts that Nazar78 did with the fan covers this is the link to get to Nazar78 model...

This just press fits on the hot end sled so that it will press the x axis end stop switch.

asked by a friend to make this so im uploading it here edit: ill have a fixed one up soon

The CR Touch connector is in a different location than the BL Touch as well as sticks out further to the left. This brings in the mount a few mm as well as relocates the connector hole. ...The cable retainer is optional.

Did a remix to fit closely to my BMG clone

This is a remix of this shroud: https://www.thingiverse.com/thing:4877288 The air ducts were too close to the bed. ... So I moved the air ducts up 2.5mm for more clearance.

This is a remix from thing:4704347, which added dual Z holding holes on the right part and a Z end trigger on the left part

23.30mm tall Dual Gear Extruder, Mount for Direct Drive Use all original hardware for your Aquila calibrated my E steps and got my retraction down to 2mm with out stringing

This direct drive setup is compatible with voxel lab Aquila and ender 3 ect... ...lightweight easy and quick to install.

This is an adjustable back plate mount for the voxel lab aquila LCD screen.(WARNING)" stock screw are too short to screw into the frame of the screen" Use a little bit longer screws for best fit. Used washers for smooth adjustments and spacing...

After having a lot of problems with leveling my bed for the Ender 3 V2 because I am a noob, this bed leveling test was very helpful for me. (Precise pictures will follow when I get a Camera) Note: Cura 4.11 has a bug that does not allow you to slice...

I love the original filament guide this is based on, but when I added a dual Z-Axis kit, I couldn't use it anymore. ... So, I created this remix that mounts the arm on the front side of the 2020 extrusion and still places the guide loop in nearly the...

I wanted a pi cam mount on the Z axis, similar to the one for the ender 3 https://www.thingiverse.com/thing:2886101 I added grip points to the shortened end stop to allow for the cam mount. I used a M3x8 bolt to secure the cam mount, but it's...

I was coverting my Aquila to direct drive, i found @FedorSosnin direct drive mount, problem was that it was using the stock extruder and i was using the dual gear one: https://de.aliexpress.com/item/1005001431887581.html I found the remix of...

<p>Remixed to allow printing upside down.</p> <p>For redesigned version without bevel: <a href="https://www.thingiverse.com/thing:5267251">https://www.thingiverse.com/thing:5267251</a></p> Category: 3D Printer Accessories

This is a remix for the Raspberry Pi 4B from Moon_buggy. I added stand offs for a Buck converter to be mounted inside the case next to the Pi. I didn't need any of the HDMI or power connections on the board. I also remixed the fan shroud to...

I really like the mount [fukumay](https://www.thingiverse.com/fukumay) created, but when I printed mine in regular PLA it flexed diagonally around the axis between the screws when clicking the display-button. ... So I made a new version with an...

Attach to the extruder bracket via the brass z-axis nut. See pictures for illustration. ... Amazon Filament Sensor: https://www.amazon.com/gp/product/B08QJDSZCL/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

So you finally decided to replace the stock extruder with the beautifull red dual gear extruder. And you found out that the filament sensor no longer aligns with the new extruder: wrong height and not in line. This adapter tackles both problems. You...