voxelab aquila upgrades 3d models

Lay the plate on its side in such a way that the conical mounds that have the holes through them that mount on the back of the carriage plate is face down. ...You want your layer lines for the stepper mount to be going vertically when the part is...

After having a lot of problems with leveling my bed for the Ender 3 V2 because I was a noob this bed leveling test was very helpful for me. (Precise pictures will follow when I get a Camera) <font color='red'>Note: Cura 4.11 has a bug that does...

Remixed to allow printing upside down. ... For redesigned version without bevel: https://www.thingiverse.com/thing:5267251

This just press fits on the hot end sled so that it will press the x axis end stop switch.

I had to reinforce the holder because the side was too weak! ...It could not support the weight of the Display in a proper way!

This is a remix of this shroud: https://www.thingiverse.com/thing:4877288 The air ducts were too close to the bed. ... So I moved the air ducts up 2.5mm for more clearance.

<p>Strange artifacts and a hole appeared when I sliced the original file by gminor in Simplify3D so I ran it through Tinkercad and filled the low spot</p> Category: 3D Printer Accessories

I love the original filament guide this is based on, but when I added a dual Z-Axis kit, I couldn't use it anymore. ... So, I created this remix that mounts the arm on the front side of the 2020 extrusion and still places the guide loop in nearly the...

This is a remix of the remix made by Rhythmreaver of an ender 3 design. The original remix had a problem with the dual gear extruder. The entry point of the filament is too high in the extruder and it wears off the filament. ... This remix makes the...

The original file had no clearance for the fan vents. ...I cut a slice off to add about 1mm clearance.

After having a lot of problems with leveling my bed for the Ender 3 V2 because I am a noob, this bed leveling test was very helpful for me. (Precise pictures will follow when I get a Camera) Note: Cura 4.11 has a bug that does not allow you to slice...

Found here https://www.printables.com/model/332268-voxelab-aquila-x-axis-mgn12-linear-rail-conversion. This version is made to work with Ender 3, Pro, V2 and Aquila printers and uses the stock X Gantry Plates. The Drive/Motor mount has 2 versions to...

This is a Hotend Fan Duct Assembly for use on a Voxelabs Aquila modified with a direct drive extruder. This is inspired by the brissfang and based on a petsfang variant with the Bullseye duct thing:2759439 This uses 2 fans -one 40mm x 20mm...

the voxelab 3D printer logo

I made it in tinkercad With the Voxelab car you can print anywhere with its giant printer #VoxelabCultsCar With the Voxelab car you can print anywhere with its giant printer #VoxelabCultsCar

This is a remix of a 5015 fitted Satsana Remix (https://www.thingiverse.com/thing:4877288). I simply raised the blower vents 2mm higher. It was too close to the bed for me. This one comes with BL/3D Touch support. This fits stock hotend. Just...

from https://www.thingiverse.com/thing:4817245 Added a holder for a DIal Indicator Used with Amazon's Neoteck DTI Digital Dial Indicator 1''/25.4mm

This is a remix from: Ender 3 Pro IR CUT Camera with Z-Axis Mount by mardun on Thingiverse: https://www.thingiverse.com/thing:4407112 and it uses the clamp piece from this model Ender 3 V2 X-Axis Tensioner Mount:...

This is a bed handle so that you can pull out the Y-axis without touching the hot plate. This is a remix of https://www.thingiverse.com/thing:4796978 which in turn is a resized remix of https://www.thingiverse.com/thing:4087329 I've added a...

I had problems with the wire in the flat cable broke / bad connection. So I designed this and it helped no problems have had since. Remember that 2 - 3 cm must be cut from the flat cable and a new 16-pin plug must be fitted. Possibly. the old plug...

UPDATED (4.06.2021) - Improved TIGHT FIT to printer frame UPDATED (5.07.2021) - After 3 print tests I achieve really good tight fit. ...If your printer prints with "elephant foot" you will need to remove it Simple filament guide - Easy snap in -...

Remixed from https://www.thingiverse.com/thing:5351558I added a space and holes for the Aluminum Filament Break Module from Amazon (https://a.co/d/7Ywuxio).Also using the 608 bearing. M3x25 Bolts & M3 Nut.Yes, I cracked the filament ring installing...

Noticed many people having problem of glass bed being ejected and in some cases shattering the glass. This update should minimize this from happening plus with the thin bed cable support make the bed spring tension uniform. Spring pocket designed to...

Drill 2 M4 holes.

Have fun

<p>Some people will mess with their X-Axis housing to use the Micro Swiss Direct Drive Extruder kit, but you can just print this out and attach it to the standoffs for the V-Slot wheels instead. ...This will save a lot of hassle.&nbsp;</p>

Have fun

Thingy remixed in 2 versions. First remix is for a spool mounted in the stock position on top of the printer. Purpose is to lift the idler pulley higher to suit the filament feed height on the dual gear extruder I use as seen in the pics. ...

A redesign of my previous anemic filament guide arm. prints in a single piece in about 2.5 hours. I made this with .4 layer height and it worked, just required a little prodding to loosen the wheel but its a great fit. although i suggest .2 layer...

Strengthened zip tie attachment points and added ramps where the cables transition onto and off the part, and it's slightly thicker.