voxelab aquila motherboard 3d models

I wanted a pi cam mount on the Z axis, similar to the one for the ender 3 https://www.thingiverse.com/thing:2886101 I added grip points to the shortened end stop to allow for the cam mount. I used a M3x8 bolt to secure the cam mount, but it's...

Slide over and screw down.

I remixed this to work with my Kette groB chain set. Tested and confirmed fitment. Worked great! Chain Set: BubbleMonk - https://www.thingiverse.com/thing:4724322 **The only thing modified was the chain link itself. The arm was not touched. ...

Simple, but effective, camera mount for Raspberry Pi cameras such as [this one](https://thepihut.com/products/raspberry-pi-camera-board-fisheye-160-lens-5mp). Designed to fit securely onto the Y axis extrusion with 4 x M4 x 12mm bolts and t-nuts.

A height increased version of the original for proper alignment with a dual extruder, you know, the typical red ones that are all over amz and eby. This is 12mm higher than original. ...If the bearing/wheel is needed grab it from the original thing but...

CRTouch mount for the Push/Pull fan shroud by [mjwanetka](https://www.thingiverse.com/mjwanetka)

BLTouch mount for the Push/Pull fan shroud by [mjwanetka](https://www.thingiverse.com/mjwanetka) Remixed from another fan shroud. ...I do not have a BLTouch so I cannot guarantee fitment.

Added an external SD card extension cable. Find part here: https://www.amazon.com/gp/product/B07YYSP5F5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Also added a clip to manage excess cable. ***Added*** Version with extended bracket so...

Attach to the extruder bracket via the brass z-axis nut. See pictures for illustration. ... Amazon Filament Sensor: https://www.amazon.com/gp/product/B08QJDSZCL/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

Using MDHR's Direct Drive mount, I didn't think it looked strong enough for a full-size stepper motor and metal extruder. My changes include full-circle mounting, instead of half-circle, so you will have to remove your wheels to install this thing. ...

I love the original filament guide this is based on, but when I added a dual Z-Axis kit, I couldn't use it anymore. ... So, I created this remix that mounts the arm on the front side of the 2020 extrusion and still places the guide loop in nearly the...

This is a remix of the remix made by Rhythmreaver of an ender 3 design. The original remix had a problem with the dual gear extruder. The entry point of the filament is too high in the extruder and it wears off the filament. ... This remix makes the...

Remixed to allow printing upside down. ... For redesigned version without bevel: https://www.thingiverse.com/thing:5267251

This mod replaces the default rotary knob with a winged one so it is possible to rotate with only one finger which is faster.Made a version with shorter wings so it hides the screen a bit less.Remix from Chrizz on Thingiverse :...

Extruder mount adjusted to clear release arm (original rubbed on my setup) and incorporated the filament guide by MDHR https://www.thingiverse.com/thing:4843185

When I installed n9jcv's fan shroud, it worked great, but the LED lights we so bright is gave me a headache to look at the printer. I created these dome shades to go over the LEDs that n9 spec'd. ... They work, although I'm sure there is a more...

So you finally decided to replace the stock extruder with the beautifull red dual gear extruder. And you found out that the filament sensor no longer aligns with the new extruder: wrong height and not in line. This adapter tackles both problems. You...

So you finally decided to replace the stock extruder with the beautifull red dual gear extruder. And you found out that the filament sensor no longer aligns with the new extruder: wrong height and not in line. This adapter tackles both problems. You...

Remix of [c2nsored's](https://www.thingiverse.com/thing:4821959) Satsana remix for V6 clone hotend. Took [TheSubaruJunkie's](https://www.thingiverse.com/thing:4817245) Satsana remix and cut off the BLTouch mount. Then just combined the two. ...

This is a remix of chubbyzook's fixed remix of JeremyLawliet's remix of the original Satsana by eric-anastas. This remix adds the BLtouch to the chubbyzook's fixed version. Will need 1 M3x8 screw right under the BLtouch mount. See images. ... ...

With my Satsana mod the original mount can't fit. With this remix you get +4mm clearance. Check photos. ... *2021/08/30* Updated, minor fixes.

I have been looking to increase the airflow over the hot end to stop heat creep as I've increased the temperature of the nozzle with different filament types. To do this I've searched for a replacement hot end cover that will accommodate a 4020...

After having a lot of problems with leveling my bed for the Ender 3 V2 because I was a noob this bed leveling test was very helpful for me. (Precise pictures will follow when I get a Camera) <font color='red'>Note: Cura 4.11 has a bug that does...

I really like the mount [fukumay](https://www.thingiverse.com/fukumay) created, but when I printed mine in regular PLA it flexed diagonally around the axis between the screws when clicking the display-button. ... So I made a new version with an...

<p>Remixed to allow printing upside down.</p> <p>For redesigned version without bevel: <a href="https://www.thingiverse.com/thing:5267251">https://www.thingiverse.com/thing:5267251</a></p> Category: 3D Printer Accessories

This is a remix of this shroud: https://www.thingiverse.com/thing:4877288 The air ducts were too close to the bed. ... So I moved the air ducts up 2.5mm for more clearance.

<p>Strange artifacts and a hole appeared when I sliced the original file by gminor in Simplify3D so I ran it through Tinkercad and filled the low spot</p> Category: 3D Printer Accessories

Lay the plate on its side in such a way that the conical mounds that have the holes through them that mount on the back of the carriage plate is face down. ...You want your layer lines for the stepper mount to be going vertically when the part is...

After having a lot of problems with leveling my bed for the Ender 3 V2 because I am a noob, this bed leveling test was very helpful for me. (Precise pictures will follow when I get a Camera) Note: Cura 4.11 has a bug that does not allow you to slice...

Slide over and screw down.