vortex throw lever 3d models

This is a simple throw lever for the Monstrum G3 6-24 Scope. ... All you will need is m3 bolt and nut to install it.

This zoom throw lever fits perfectly on the Athlon Ares ETR 4.5-30x56 rifle scope, requiring minimal adjustments to ensure a precise fit. It is compatible with M3 thread inserts measuring 4 mm x 5 mm. ... Printed successfully from both PLA and ABS...

Throw lever designed to fit Leupold VX-3 and VX-iiiL scopes, however it most likely fits other Leupold scopes as well (scopes with a ≈ 37.7 mm zoom ring and the gas inlet notch). At full magnification, the throw lever has good clearance for both the...

A throw lever designed for the Athlon Ares BTR Gen 1 scope. ...It should also fit the Ares ETR Gen 1 and the Midas Tac, although I have not tested that.Hardware required:1 M3x10 screw1 M3 nutCategory: Sport & Outdoors

Roue de réglage de parallaxe + levier de grossissement pour lunette vector optics continental (5-30x56). ...À monter en force. Parallax adjusment wheel + throw lever for vector optics continental scope (5-30x56). ...Interference fit.

This is a throw lever for the Athlon Talos BTR 1-4X24 rifle scope. ...It slides over the magnification ring and uses an M4 Screw and bolt to tighten it onto the scope.

... SLX brakes I bought a set of Shimano Deore 6100 hydraulic brakes. ...Everything worked but I needed an allan key to adjust the throw on the lever. ...After a quick design on Onshape CAD software it was set to glue into the lever and start using it.

This is a throw lever designed for the Athlon Ares BTR Gen 1 scope. It should also fit the Ares ETR Gen 1 and the Midas Tac REVIII, although I have not tested that. ...   Requires 1 M3x10 screw and 1 M3 nut.

Re-mix from the throw lever by jitblass. I fixed the messed up geometry, beveled the edges (so you don't have to sand them afterwards), and shrunk the cutout for the nut to accept standard M3 nuts. Once printed, you'll need a M3 x 10 screw and...

I'm trying out the magnification throw lever that fits my Sig Tango 6 4-24x50 scope. I'm not sure if this will fit other SIG scopes in the tango line or their other models, so I'd appreciate feedback from anyone who tries it on different SIG scope...

This remix draws inspiration from miprotera's 'Bushnell 1x-4x Quick Adjustment Throw Lever', which can be found here: https://www.thingiverse.com/thing:2566788 The changes made include: Thickness is boosted by 0.3mm to enhance durability. Sides are...

Throw lever for Primary Arms 1-6x SFP scopes. This is an original design. **TABLE OF CONTENTS** - Parts - Printing Details **PARTS** - (1) M3x12mm socket head screw - (1) M3 nut **PRINTING DETAILS** - Settings (Tested on ender...

The Cat Tail Lever attachment is designed to complement the Optisan Mamba 1-4x scope, which had a limited release a couple of years back. ...This custom component was 3D printed without any support structures.

Primary Arms Scope Throw LeverSLx6 Silver Series 1-6"Beefy" to last awhileRecommend course screw of appropriate size and length.Starter hole provided, Predrill hole to avoid cracking.Will clear mid height scope rings in higher. ... Probably won't work...

This lever is specifically crafted for the Athlon Ares BTR Gen 1 scope. It should also be compatible with the Ares ETR Gen 1 and the Midas Tac REVIII, though I haven't tested it on those models yet. Required hardware includes: 1. An M3x10 screw 2.

... stiffer. ...When loading magazines with match ammo that is very greasy it makes turning the know almost impossible. SO I designed a Throw leaver to make it much easier to turn. ... It just requires 1 - 3M x 16mm socket head cap screw and 3mm Nut

It's best to test the lever's fit by scaling up or down after printing at a lower resolution initially. Relying on rafts may not be necessary on most printers, but I used them to avoid an elephant's foot on the base layer. ...Scale everything in the...

Switchview lever for Vortex Razor HD Gen II Recommended to printed with strong filament such as nylon or PC First file is the prototype (tested and works) Second file a new prototype. THIS IS A WORK IN PROGRESS. I WOULD PRINT A FEW JUST IN CASE...

The CAD can be found from https://github.com/eamars/PrintableThrowLevers/tree/main

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/2gWa0k5Wp6Q

Rallonge de réglage pour lunette sieghtmark latitude Nécessite une vis m2/12 et un écrou m2 frein de préférence Mon print

A handheld trigger created to complement a Nikon Monarch Riflescope, tailored precisely for the 5-20x42mm variant.

Primary Arms throw lever. 2.5-10x. ... Will need nut+ screw

Athlon Ares BTR 4.5-27x50 Scope Throw Lever. ...Latest iteration featuring a 41.5mm ring. Complete package including all necessary files. This marks the culmination of previous efforts to optimize the parametric scope throw lever design.

Throw lever designed for the Barska Euro-30 4A 1.25-4.5x LPVO. ... Hardware needed: Any screw and nut that fits

Throw lever for original Strike Eagle 1-6. Design uses just a M3 screw directly into the plastic. ...I used PETG for the durability and ease of getting around the 30mm tube but PLA will work too.

The Throw Lever simplifies the process of adjusting the zoom on your riflescope, especially in chilly temperatures when it's harder to make adjustments without this handy feature. The clamping force is applied using a self-tapping screw with a...

Throw the lever for Meopta's K-Dot 1-4 and its variation, the Meostar R1. It works seamlessly, having been put to use for an extended period in cold temperatures without malfunctioning. ...A crucial requirement for this setup is a M3 machine bolt and...

... onto the zoom ring one way - the smaller diameter smooth ring faces back towards the rifle stock. You have to slightly stretch the ring open to get it in place - the smaller diameter smooth part stops the throw lever from sliding off the zoom ring.

This is a remix I did of two Scope Throw Levers on Thingiverse. It was designed to fit the Primary Arms ACSS Raptor 1-6 FFP Scope perfectly without any scaling required, even when printing with ABS material. I printed the part at 100% infill and...